- 您現在的位置：買賣IC網 > PDF目錄362397 > ARA210A24 MICROWAVE RELAY FOR ATTENUATOR CIRCUIT PDF資料下載
參數資料
| 型號： | ARA210A24 |
| 英文描述： | MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
| 中文描述： | 微波中繼的衰減器電路 |
| 文件頁數： | 3/3頁 |
| 文件大小： | 208K |
| 代理商： | ARA210A24 |
9/1/2000
RA
REFERENCE DATA
1. High frequency characteristics
Sample: ARA200A12
Measuring method: Measured with HP network analyzer (HP8753C).
Insertion loss
Isolation
V.S.W.R.
0.8
1.0
0
0.2
0.6
0.4
0.3
300kHz
0.5GHz
Frequency
1.0GHz
COM-NC
COM-NO
I
80
100
0
20
30
60
40
300kHz
0.5GHz
Frequency
1.0GHz
COM-NC
COM-NO
CONTACT sets
I
1.1
1.0
1.5
1.4
1.2
1.3
300kHz
0.5GHz
Frequency
1.0GHz
COM-NO
COM-NC
V
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be rectangu-
lar. If it includes ripple, the ripple factor
should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different. The nominal operating voltage
should be applied to the coil for more
than 10 ms to set/reset the latching type
relay.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or mal-
function.
3. External magnetic field
Since RA relays are highly sensitive po-
larized relays, their characteristics will be
affected by a strong external magnetic
field. Avoid using the relay under that
condition.
4. Cleaning
For automatic cleaning, the boiling meth-
od is recommended. Avoid ultrasonic
cleaning which subjects the relays to high
frequency vibrations, which may cause
the contacts to stick.
It is recommended that alcoholic solvents
be used.
5. Soldering
Manual soldering shall be performed un-
der following condition.
Tip temperature: 280°C to 300°C
.536°F
to 572°F
Wattage: 30 to 60W
Soldering time: within 5s
In case of automatic soldering, the follow-
ing conditions should be observed
1) Position of measuring temperature
2) IR (infrared reflow) soldering method
Temperature rise of relay itself may vary
according to the mounting level or the
heating method of reflow equipment.
Therefore, please set the temperature of
soldering portion of relay terminal and
the top surface of the relay case not to
exceed the above mentioned soldering
condition.
It is recommended to check the tempera-
ture rise of each portion under actual
mounting condition before use.
The soldering earth shall be performed
by manual soldering.
B
1.0mm
.039inch
A: Surface of PC board where relay is mounted.
B: Above the PC board surface.
A
T
1
T
2
T
3
T
4
T
5
t
1
t
3
t
4
t
5
t
2
A:
B:
t
2
- t
1
= 80 to 120 s
t
5
- t
3
= 30 to 40 s
t
4
= 170 to 190 s
T
1
=150
°
C
302
°
F
T
2
=160
°
C
320
°
F
T
3
=183
°
C
361
°
F
T
4
=245
°
C
473
°
F
T
5
=270
°
C
518
°
F
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
All Rights Reserved, Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog
相關PDF資料 |
PDF描述 |
|---|---|
| ARA210A48 | MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
| ARA210A4H | MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
| ARA220A03 | MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
| ARA220A05 | MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
| ARA220A06 | MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ARA210A24J | 制造商:Panasonic Electric Works 功能描述: |
| ARA210A48 | 制造商:NAIS 制造商全稱:Nais(Matsushita Electric Works) 功能描述:MICROWAVE RELAY FOR ATTENUATOR CIRCUIT |
| ARA210A4H | 功能描述:高頻/射頻繼電器 2 Form C, 4.5VDC 2 Form C 1 RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz |
| ARA210A4HJ | 制造商:Panasonic Electric Works 功能描述: |
| ARA220A03 | 功能描述:高頻/射頻繼電器 2 Form C, 3VDC 2 Form C 1 RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz |
發布緊急采購，3分鐘左右您將得到回復。