- 您現在的位置：買賣IC網 > PDF目錄364693 > APCI-IB40 PCI-BUS I/O CARD PDF資料下載
參數資料
| 型號： | APCI-IB40 |
| 英文描述： | PCI-BUS I/O CARD |
| 中文描述： | PCI總線的I / O卡 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 251K |
| 代理商： | APCI-IB40 |
2192-09125-000-000
Page 8
J605 APCI-ADADIO
Utility Disk
A demonstration program has been provided on the utility disk ADADIO.EXE.
This can be used to aid calibration and as source code is provided it will help demonstrate the
method used for accessing devices.
ADADIO.EXE
This program will display the ADC inputs, scroll an active bit along the digital I/O and allows setting
of the DACs. These will work with standard link settings. Decrementing counter/timer counts and
incrementing interrupt counts are also displayed, but a link must be fitted between pins 9 and 10 on
PL3.
ADADIO.INI
This is a text file which is used by the ADADIO program to select the number of channels, ADC and
DAC ranges etc. This file can be edited to reflect any changes in the board settings.
Calibration
Calibrating the ADC
In order to calibrate the ADC it is necessary to use a precision digital voltmeter (DVM) with at least
5 digit resolution and a high stability low noise DC signal source. During calibration it is necessary
to continually read and display the ADC data. A program ADADIO.EXE has been provided on the
utility disk to enable this.
Two trim adjusters, VR7 and VR1 , are provided for trimming the zero offset and gain respectively.
These trims are for fine-adjusting the standard ranges.
Unipolar Calibration
Set the necessary links for unipolar operation and the required voltage range. Run the ADADIO.EXE
program.
Zero Offset Adjust
1) Set the input voltage to 0.0000V.
2) Adjust VR7 to give 000 to 001 hex.
Full Scale Gain Adjust
1) Set the input voltage to full scale minus 1 LSB
+4.9985 for the 5V range.
+9.9975 for the 10V range.
2)Adjust VR1 to give FFE to FFF.
Bipolar Calibration
Set the necessary links for bipolar operation and the required voltage range. Run the ADADIO.EXE
program.
Bipolar Offset Adjust
1) Set the input voltage to full scale negative plus 1 LSB
-4.9975 for the 5V range.
-9.9950 for the 10V range.
2) Adjust VR7 to give 000 to 001 hex.
相關PDF資料 |
PDF描述 |
|---|---|
| APCI-SER4 | PCI-BUS I/O CARD |
| APD1510-000 | APD Series:Silicon PIN Diode Chips|PIN Diodes: General Purpose Switching PIN Diodes |
| APD1520-000 | APD Series:Silicon PIN Diode Chips|PIN Diodes: General Purpose Switching PIN Diodes |
| APD2520CGCK03 | 4.5x2mm SMD CHIP LED LAMP |
| APD2520EC03 | 4.5x2mm SMD CHIP LED LAMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APCI-RELAY8/IN8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI-BUS I/O CARD |
| APCI-SER4 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI-BUS I/O CARD |
| APCITE | 制造商:Pentair Technical Products / Hoffman 功能描述:Operator Adapter, I.T.E. , for I-T-E Max-Flex, Steel |
| APCMB012 | 制造商:Amphenol Corporation 功能描述:MS3106E24-AJP W/OUT CNTS |
| APCMB108 | 制造商:Amphenol RF 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。