- 您現在的位置：買賣IC網 > PDF目錄381262 > APA4801JI-TU (Anpec Electronics Corporation) Stereo 280mW 8 OHM Speaker Driver with Mute PDF資料下載
參數資料
| 型號： | APA4801JI-TU |
| 廠商： | Anpec Electronics Corporation |
| 元件分類： | 音頻放大器 |
| 英文描述： | Stereo 280mW 8 OHM Speaker Driver with Mute |
| 中文描述： | 280mW 8立體聲揚聲器驅動器，帶有靜音 |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 132K |
| 代理商： | APA4801JI-TU |
Copyright
ANPEC Electronics Corp.
Rev. A.5 - Apr., 2001
APA4801
www.anpec.com.tw
10
Input Capacitor, Ci
In the typical application an input capacitor , Ci , is
required to allow the amplifier to bias the input signal
to the proper DC level for optimum operation . In this
case , the external capacitor Ci and the internal re-
sistance Ri form a high-pass filter with the corner fre-
quency determined in the follow equation :
fc (highpass)= 1/ (2
π
RiCi)
The value of Ci is important to consider as it directly
affects the low frequency performance of the circuit .
Consider the APA4801 where Ri is 130k
internal
fixed . Equation is reconfigured as follow :
Ci= 1/(2
π
*130k
*fc)
And the ceramic capacitor is recommanded
(1)
(2)
Bias Capacitor, Cb
As with any power amplifier , proper supply bypass-
ing is critical for low noise performance and high
power supply rejection . The capacitor location on
both the bypass and power supply pins should be as
close to the device as possible . The effect of a larger
half supply bias capacitor is improved PSRR due to
increased half-supply stability . Typical applications
employ a 5V regulator with 10
μ
F and a 0.1
μ
F bias
capacitors which aid in supply filtering . This does
not eliminate the need for bypassing the supply nodes
of the APA4801 . The selection of bias capacitors ,
especially Cb , is thus dependent upon desired PSRR
requirements , click and pop performance . The ca-
pacitor is fed from a 50k
source inside the amplifier.
To keep the start-up pop as low as possible , the
relationship shown in equation should be maintained.
1/(Cb*50k
)
≤
1/{Ci*Ri}
As an example , consider a circuit where Cb is
4.
7μ
F , Ci is 1
μ
F and Ri is 130k
Inserting these
values into the equation we get 4.26
≤
7.69 which
satisfies the rule . Bias capacitor , Cb , values of
2.2
μ
F to 10
μ
F ceramic or tantalum low-ESR capaci-
tors are recommended for the best THD and noise
performance.
(3)
Output Coupling Capacitor, Cc
In the typical single-supply SE configuration , an out-
put coupling capacitor (Cc) is required to block the
DC bias at the output of the amplifier thus preventing
DC currents in the load . As with the input coupling
capacitor , the output coupling capacitor and imped-
ance of the load form a high-pass filter governed by
equation .
fc(highpass)= 1/(2
π
R
Cc)
For example , a 220
μ
F capacitor with an 32
speaker
would attenuate low frequencies below 22Hz . The
main disadvantage , from a performance standpoint,
is the load impedance is typically small , which drives
the low-frequency corner higher degrading the bass
response . Large values of Cc are required to pass
low frequencies into the load .
(4)
Optimizing Depop Circuitry
When the amplifier is in mute mode , both of the out-
put stage and input bypass continues to be biased .
And no pop noise will be heard during the transition
out of mute mode .
Power Supply Decoupling , Cs
APA4801 is a high-performance CMOS audio ampli-
fier that requires adequate power supply decoupling
to ensure the output total harmonic distortion (THD)
is as low as possible . Power supply decoupling also
prevents the oscillations causing by long lead length
between the amplifier and the speaker . The optimum
decoupling is achieved by using two different type
capacitors that target on different type of noise on
the power supply leads . For higher frequency tran-
sients , spikes , or digital hash on the line , a good
low equivalent-series-resistance (ESR) ceramic ca-
pacitor , typically 0.1
μ
F placed as close as possible
to the device V
frequency noise signals , a large aluminum electro-
lytic capacitor of 10
μ
F or greater placed near the audio
power amplifier is recommended .
lead works best . For filtering lower-
Application Note
相關PDF資料 |
PDF描述 |
|---|---|
| APA4801 | Stereo 280mW 8 OHM Speaker Driver with Mute |
| APA4835RI-TU | Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
| APA4835RI-TR | Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
| APA4835 | Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
| APA4838RI-TR | Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APA4801KI-TR | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 280mW 8 OHM Speaker Driver with Mute |
| APA4801KI-TU | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 280mW 8 OHM Speaker Driver with Mute |
| APA4835 | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
| APA4835RI-TR | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
| APA4835RI-TU | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:Stereo 2.8W Audio Power Amplifier with DC Volume Control and Selectable Gain |
發布緊急采購，3分鐘左右您將得到回復。