ProASICPLUS Flash Family FPGAs 2- 8 v5.9 Boundary Scan (JTAG) P" />
參數資料
型號： APA075-FG144
廠商： Microsemi SoC
文件頁數： 89/178頁
文件大?。?/td> 0K
描述： IC FPGA PROASIC+ 75K 144-FBGA
標準包裝： 160
系列： ProASICPLUS
RAM 位總計： 27648
輸入/輸出數： 100
門數： 75000
電源電壓： 2.3 V ~ 2.7 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 70°C
封裝/外殼： 144-LBGA
供應商設備封裝： 144-FPBGA（13x13）
ProASICPLUS Flash Family FPGAs
2- 8
v5.9
Boundary Scan (JTAG)
ProASICPLUS devices are compatible with IEEE Standard
1149.1, which defines a set of hardware architecture and
mechanisms for cost-effective, board-level testing. The
basic ProASICPLUS boundary-scan logic circuit is composed
of the TAP (test access port), TAP controller, test data
registers, and instruction register (Figure 2-9). This circuit
supports all mandatory IEEE 1149.1 instructions (EXTEST,
SAMPLE/PRELOAD
and
BYPASS)
and
the
optional
IDCODE instruction (Table 2-6).
Each test section is accessed through the TAP, which has
five associated pins: TCK (test clock input), TDI and TDO
(test data input and output), TMS (test mode selector)
and TRST (test reset input). TMS, TDI and TRST are
equipped with pull-up resistors to ensure proper
operation when no input data is supplied to them. These
pins are dedicated for boundary-scan test usage. Actel
recommends that a nominal 20 k
Ω pull-up resistor is
added to TDO and TCK pins.
The TAP controller is a four-bit state machine (16 states)
that operates as shown in Figure 2-10 on page 2-9. The
1s and 0s represent the values that must be present at
TMS at a rising edge of TCK for the given state transition
to occur. IR and DR indicate that the instruction register
or the data register is operating in that state.
ProASICPLUS devices have to be programmed at least
once for complete boundary-scan functionality to be
available. Prior to being programmed, EXTEST is not
available. If boundary-scan functionality is required prior
to programming, refer to online technical support on the
Actel website and search for ProASICPLUS BSDL.
Figure 2-9 ProASICPLUS JTAG Boundary Scan Test Logic Circuit
Device
Logic
TDI
TCK
TMS
TRST
TDO
I/O
Bypass Register
Instruction
Register
TAP
Controller
Test Data
Registers
Table 2-6
Boundary-Scan Opcodes
Hex Opcode
EXTEST
00
SAMPLE/PRELOAD
01
IDCODE
0F
CLAMP
05
BYPASS
FF
Table 2-6
Boundary-Scan Opcodes
Hex Opcode
相關PDF資料
PDF描述
HBC65DRYI-S93 CONN EDGECARD 130PS DIP .100 SLD
APA075-FGG144 IC FPGA PROASIC+ 75K 144-FBGA
ESC60DRYS-S93 CONN EDGECARD 120PS DIP .100 SLD
A40MX02-1PLG44I IC FPGA MX SGL CHIP 3K 44-PLCC
ACC44DRES-S734 CONN EDGECARD 88POS .100 EYELET
相關代理商/技術參數
參數描述
APA075-FG144A 功能描述:IC FPGA PROASIC+ 75K 144-FBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17）
APA075-FG144I 功能描述:IC FPGA PROASIC+ 75K 144-FBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17）
APA075-FG896A 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:Automotive-Grade ProASIC Flash Family FPGAs
APA075-FGB 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA075-FGES 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*