- 您現在的位置：買賣IC網 > PDF目錄166226 > AP601-F 800 MHz - 2000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | AP601-F |
| 元件分類： | 放大器 |
| 英文描述： | 800 MHz - 2000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| 封裝： | 5 X 6 MM, ROHS COMPLIANT, SMT, DFN-14 |
| 文件頁數： | 4/10頁 |
| 文件大小： | 767K |
| 代理商： | AP601-F |
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com
Page 3 of 10 May 2007 ver 1
AP601
High Dynamic Range 1.8W 28V HBT Amplifier
Application Circuit PC Board Layout
Circuit Board Material: 0.0147” Rogers Ultralam 2000, single layer, 1 oz
copper,
εr = 2.45, Microstrip line details: width = .042”, spacing = .050”
Baseplate Configuration
Notes:
1. Please note that for reliable operation, the evaluation board will have to be mounted to a much larger
heat sink during operation and in laboratory environments to dissipate the power consumed by the
device. The use of a convection fan is also recommended in laboratory environments.
2. The area around the module underneath the PCB should not contain any soldermask in order to
maintain good RF grounding.
3. For proper and safe operation in the laboratory, the power-on sequencing is recommended.
Evaluation Board Bias Procedure
Following bias procedure is recommended to ensure proper functionality of AP601 in a laboratory environment. The sequencing is not
required in the final system application.
Bias.
Voltage (V)
Vcc
+28
Vbias
+5
Vpd
+5
Turn-on Sequence:
1.
Attach input and output loads onto the evaluation board.
2.
Turn on power supply Vcc = +28V.
3.
Turn on power supply Vbias = +5V. At this point, the only current drawn by the device is leakage current (< 25μA).
4.
Turn on power supply Vpd = +5V. Power supply Vcc should now be drawing typical Icq = 40 mA.
5.
Turn on RF power.
Turn-off Sequence:
1.
Turn off RF power.
2.
Turn off power supply Vpd = +5V.
3.
Turn off power supply Vbias = +5V.
4.
Turn off power supply Vcc = +28V.
Notes:
1.
Icq can be adjusted with the resistor R2 from the Vpd (+5V) supply and the PIN_VPD (pin14) of the amplifier. Increasing R2
results in a lower Icq. Icq should not be increased above 80mA.
2.
Vpd is used as a reference for the internal active bias circuitry. It can be used to turn on/off the amplifier. Ipd depends on the Icq
quiescent current setting. Ipd can be up to 2mA at a quiescent current setting of 40mA.
3.
Vbias should be maintained fixed at +5V. Ibias will change based on RF input power level. It can be up to 2mA on the AP601.
Ipd vs Icq
0
0.5
1
1.5
2
020
40
60
80
100
Icq Setting (mA)
Ip
d
(
m
A
)
Ibias vs Output Power
0
0.5
1
1.5
2
18
20
22
24
26
28
Output Average Power (dBm)
Ib
ia
s
(
m
A
)
相關PDF資料 |
PDF描述 |
|---|---|
| AP7217C-13SPG-U | 1.25 V FIXED POSITIVE LDO REGULATOR, PDSO8 |
| AP7S1-FREQ-R-T | CRYSTAL OSCILLATOR, CLOCK, 10 MHz - 166 MHz, HCMOS/TTL OUTPUT |
| AP7S-200MHZ-L-R-T | CRYSTAL OSCILLATOR, CLOCK, 200 MHz, HCMOS/TTL OUTPUT |
| AP7S-10MHZ-N-R | CRYSTAL OSCILLATOR, CLOCK, 10 MHz, HCMOS/TTL OUTPUT |
| AP7S-FREQ-N-T | CRYSTAL OSCILLATOR, CLOCK, 10 MHz - 200 MHz, HCMOS/TTL OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP601-PCB1960 | 功能描述:射頻開發工具 1930-1990MHz Brd 15dB Gain RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| AP601-PCB2140 | 功能描述:射頻開發工具 2110-2170MHz Brd 13.5dB Gain RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| AP601-PCB900 | 功能描述:射頻開發工具 869-960MHz Eval Brd 16dB Gain RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| AP602 | 制造商:WJCI 制造商全稱:WJCI 功能描述:High Dynamic Range 4W 28V HBT Amplifier |
| AP-602 | 功能描述:AIR FILTRATION PANEL AP-602 制造商:3m 系列:Versaflo?，AP-600 零件狀態:有效 類型:空氣過濾面板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。