- 您現在的位置：買賣IC網 > PDF目錄362357 > AP1212LNLA Dual USB High-Side Power Switch PDF資料下載
參數資料
| 型號： | AP1212LNLA |
| 英文描述： | Dual USB High-Side Power Switch |
| 中文描述： | 雙USB高端功率開關 |
| 文件頁數： | 1/11頁 |
| 文件大?。?/td> | 246K |
| 代理商： | AP1212LNLA |
AP1212
Dual USB High-Side Power Switch
Features
- Compliant to USB specifications
- Dual independent switches control
- 2.7V to 5.5V input voltage
- 500mA minimum continuous current per port
- 110m
Ω
typical on-resistance
- 1.25A maximum short circuit current limit
- Independent open-drain fault flag pins
- 110
μ
A typical on-state supply current
- 1
μ
A typical off-state supply current
- Output can be forced higher than input (off-state)
- Thermal shutdown
- 2.4V typical under voltage lockout (UVLO)
- 1ms turn-on (soft-start) and fast turn-off
- Enable active-high (H) or active-low (L)
- 8-pin SOP and PDIP packages
Applications
USB hubs
Hot plug-in power supplies
Battery-charger circuits
Pin Assignments
(Top View)
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev. 1.0 Sep.23, 2004
1/11
General Description
The AP1212 series are dual integrated high-side
power switch with independent enable and flag
functions,
optimized
for
bus-powered
Universal
applications. The AP1212 series support the
following USB requirements: each switch channel
supplies up to 500mA as required by USB
downstream devices; the switch’s low on-resistance
meets USB voltage drop requirements; fault current
is limited to typically 1000mA, well below the UL
25VA safety requirements; and a flag output is
available to indicate fault conditions to the local
USB controller. Soft start eliminates the momentary
voltage drop on the upstream port that may occur
when the switch is enabled in bus-powered
applications.
Additional features include thermal shutdown to
prevent catastrophic switch failure from high-current
loads, under voltage lockout (UVLO) to ensure that
the device remains off unless there is a valid input
voltage present, and 3.3V and 5V logic compatible
enable inputs.
self-powered
Serial
and
Bus
(USB)
EN1
EN2
FLG1
FLG2
1
2
3
4
8
7
6
5 OUT2
OUT1
GND
IN
PDIP/SOP
AP1212
Pin Descriptions
Name
Enable: Logic-compatible enable
input. ( H: active high, L: active low).
Do not float.
Description
EN1
EN2
FLG1
FLG2
Fault Flag: Active-low, open-drain
output. Indicates over current,
UVLO, and thermal shutdown.
GND
Supply return.
Supply Input: Output MOSFET drain.
Also supplies IC’s internal circuitry.
Connect to positive supply.
Switch Output: Output MOSFET
source. Typically connect to
switched side of load.
IN
OUT1
OUT2
相關PDF資料 |
PDF描述 |
|---|---|
| AP1212 | Dual USB High-Side Power Switch |
| AP1212HN | Dual USB High-Side Power Switch |
| AP1212HS | Dual USB High-Side Power Switch |
| AP1212HSA | Dual USB High-Side Power Switch |
| AP1212HSL | Dual USB High-Side Power Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP1212LS | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Dual USB High-Side Power Switch |
| AP1212LSA | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Dual USB High-Side Power Switch |
| AP1212LSG-13 | 功能描述:電源開關 IC - USB INTERFCE USB LO CMOS 1A 0.7V MAX 2.7-5.5V RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| AP1212LSG-U | 制造商:DIODES 制造商全稱:Diodes Incorporated 功能描述:DUAL USB HIGH-SIDE POWER SWITCH |
| AP1212LSL | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Dual USB High-Side Power Switch |
發布緊急采購，3分鐘左右您將得到回復。