- 您現在的位置：買賣IC網 > PDF目錄375340 > AOZ1012D (ALPHA) EZBuck⑩ 3A Simple Buck Regulator PDF資料下載
參數資料
| 型號： | AOZ1012D |
| 廠商： | ALPHA |
| 英文描述： | EZBuck⑩ 3A Simple Buck Regulator |
| 中文描述： | EZBuck⑩3A條簡單的降壓穩壓器 |
| 文件頁數： | 8/17頁 |
| 文件大小： | 807K |
| 代理商： | AOZ1012D |
^lwNMNOa
Detailed Description
AOZ1012D is a current-mode step down regulator with
integrated high side PMOS switch and a low side
freewheeling Schottky diode. It operates from a 4.5V to
16V input voltage range and supplies up to 3A of load
current. The duty cycle can be adjusted from 6% to
100% allowing a wide range of output voltage. Features
include enable control, Power-On Reset, input under
voltage lockout, fixed internal soft-start and thermal
shut down.
AOZ1012D is available in thermally enhanced DFN-8
package.
Enable and Soft Start
AOZ1012D has internal soft start feature to limit in-rush
current and ensure the output voltage ramps up
smoothly to regulation voltage. A soft start process
begins when the input voltage rises to 4.0V and voltage
on EN pin is HIGH. In soft start process, the output
voltage is ramped to regulation voltage in typically 4ms.
The 4ms soft start time is set internally.
The EN pin of the AOZ1012D is active high. Connect the
EN pin to VIN if enable function is not used. Pull it to
ground will disable the AOZ1012D. Do not leave it open.
The voltage on EN pin must be above 2.0 V to enable
the AOZ1012D. When voltage on EN pin falls below 0.6
V, the AOZ1012D is disabled. If an application circuit
requires the AOZ1012D to be disabled, an open drain or
open collector circuit should be used to interface to EN
pin.
Steady-State Operation
Under steady-state conditions, the converter operates
in fixed frequency and Continuous-Conduction Mode
(CCM).
AOZ1012D integrates an internal P-MOSFET as the
high-side switch. Inductor current is sensed by
amplifying the voltage drop across the drain to source
of the high side power MOSFET. Output voltage is
divided down by the external voltage divider at the FB
pin. The difference of the FB pin voltage and reference
is amplified by the internal transconductance error
amplifier. The error voltage, which shows on the COMP
pin, is compared against the current signal, which is
sum of inductor current signal and ramp compensation
signal, at PWM comparator input. If the current signal is
less than the error voltage, the internal high-side switch
is on. The inductor current flows from the input through
the inductor to the output. When the current signal
exceeds the error voltage, the high-side switch is off.
April 2006
www.aosmd.com
Page 8 of 17
The inductor current is freewheeling through the internal
Schottky diode to output.
The AOZ1012D uses a P-Channel MOSFET as the high
side switch. It saves the bootstrap capacitor normally
seen in a circuit which is using an NMOS switch. It
allows 100% turn-on of the upper switch to achieve
linear regulation mode of operation. The minimum
voltage drop from V
to V
is the load current times DC
resistance of MOSFET plus DC resistance of buck
inductor. It can be calculated by equation below:
I
V
V
×
=
Where V
O_MAX
is the maximum output voltage;
V
IN
I
O
is the output current from 0A to 3A;
R
is the on resistance of internal
MOSFET, the value is between 40m and 85m
depending on input voltage and junction
temperature;
R
inductor
is the inductor DC resistance;
Switching Frequency
The AOZ1012D switching frequency is fixed and set by
an internal oscillator. The actuall switching frequency
could range from 350kHz to 600kHz due to device
variation.
Output Voltage Programming
Output voltage can be set by feeding back the output to
the FB pin with a resistor divider network. In the
application circuit shown in Figure 1. The resistor divider
network includes R
1
and R
. Usually, a design is started
by picking a fixed R
value and calculating the required
R1 with equation below.
)
(
)
(
_
inductor
R
ON
DS
O
IN
MAX
O
R
+
)
1
8
2
1
R
R
V
O
+
×
=
Some standard value of R
, R
for most commonly used
output voltage values are listed in Table 1.
Table 1.
Vo (V)
R1 (k
)
0.8
1.0
1.2
4.99
1.5
10
1.8
12.7
2.5
21.5
3.3
31.6
5.0
52.3
R2 (k
)
open
10
11.5
10.2
10
10
10
相關PDF資料 |
PDF描述 |
|---|---|
| AOZ1012DI | EZBuck⑩ 3A Simple Buck Regulator |
| AOZ1013AI | EZBuck TM 3A Simple Buck Regulator |
| AOZ1013 | EZBuck TM 3A Simple Buck Regulator |
| AOZ1014 | EZBuck TM 5A Simple Buck Regulator |
| AOZ1014AI | EZBuck TM 5A Simple Buck Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AOZ1012DI | 功能描述:IC REG BUCK ADJ 3A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:EZBuck™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| AOZ1013 | 制造商:AOSMD 制造商全稱:Alpha & Omega Semiconductors 功能描述:EZBuck TM 3A Simple Buck Regulator |
| AOZ1013AI | 制造商:AOSMD 制造商全稱:Alpha & Omega Semiconductors 功能描述:EZBuck TM 3A Simple Buck Regulator |
| AOZ1013AI_09 | 制造商:AOSMD 制造商全稱:Alpha & Omega Semiconductors 功能描述:EZBucka?￠ 3A Simple Regulator |
| AOZ1014 | 制造商:AOSMD 制造商全稱:Alpha & Omega Semiconductors 功能描述:EZBuck TM 5A Simple Buck Regulator |
發布緊急采購，3分鐘左右您將得到回復。