- 您現在的位置：買賣IC網 > PDF目錄375328 > AN8267S (PANASONIC CORP) ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting PDF資料下載
參數資料
| 型號： | AN8267S |
| 廠商： | PANASONIC CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting |
| 中文描述： | BRUSH DC MOTOR CONTROLLER, 1.5 A, PDSO16 |
| 封裝： | 0.300 INCH, PLASTIC, SOP-16 |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 53K |
| 代理商： | AN8267S |
power line
The power pin of the AN8267S is the Pin12. Separate it
from the power line to the moter coil. Wiring to the motor
coil should be made as thick and short as possible.
GND line
The AN8267S has two GND Pins (8 and 13). Since the
Pin8 serves as the GND pin for the coil output power transis-
tor, separate from GND of the Pin13 as much as possible.
Wiring to the Pin8 should be also as thick and short as possi-
ble.
The Pin3 is switched over in synchronization with coil cur-
rent supply/stop.
The maximum applied voltage for both Pins2 and 3 is 55V.
5. TSD (Thermal Shut Down)Pin5
The AN8267S incorporates the overheat protective circuit.
If the chip temperature of the IC reaches 150C (typ.), the
coil current stops. Since the Pin5 is a TSD circuit operation
checking pin, leave it “open” when the motor is driving nor-
mally.
7. Precautions for wiring
When mounting the AN8267S onto the PCB, pay attention
to the following points as to its wiring.
6. Hall input Pins1 and 16
Input a sine wave signal from the Hall element to the Pins1
and 16.
The input DC voltage of those pins should be 2V
min.
or
more.
It is recommended to connect the Hall element and DC
bias resistor between the Pins1 and GND.
The Hall element sine wave signal Vi to be input to the
Pins1 and 16 should be ; 15mV
p–p
Vi 400mV
p–p
1. Coil current ON : L
2. Coil current OFF : H
AN8267S
AN8267S
14
1
16
Hall Element
R : DC Bias Resistor
Fig.7
Fig.8
14
12
Separate
Hall Element
Separate
IC Power Supply
Coil Power Supply
PGND
GND
Counterflow Preventive Diode
4
8
13
11
6
10
1
16
I
Supplementary Explanation (Cont.)
<
<
相關PDF資料 |
PDF描述 |
|---|---|
| AN826 | RECOMMENDED MINIMUM PADS FOR SC-70: 3-LEAD |
| AN8353UB | High Efficiency Car Dashboard Dimmer IC |
| AN8377N | 3-channel Linear Driver |
| AN8473SA | Spindle motor driver IC for optical disk |
| AN8480NSB | 3-phase full-wave motor driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN827-12J | 制造商:undefined 功能描述: |
| AN827-4D | 制造商: 功能描述: 制造商:undefined 功能描述: |
| AN827-6D | 制造商: 功能描述: 制造商:undefined 功能描述: |
| AN8280 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:主導軸馬達直接驅動電路 |
| AN8281S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:主導軸馬達直接驅動電路 |
發布緊急采購，3分鐘左右您將得到回復。