- 您現在的位置：買賣IC網 > PDF目錄364677 > AN1207 (飛思卡爾半導體(中國)有限公司) THE MC145170 in Basic HF and VHF Oscillators PDF資料下載
參數資料
| 型號： | AN1207 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | THE MC145170 in Basic HF and VHF Oscillators |
| 中文描述： | 在基本高頻和甚高頻MC145170振蕩器 |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 267K |
| 代理商： | AN1207 |
AN1207
3
MOTOROLA
The C Register, which configures the device, is pro-
grammed with $C0 (1 byte). This sets the phase detector to
the proper polarity and activates PDout. This also turns off the
unused outputs. The phase detector polarity is determined by
the filter and the VCM. For this example, the MC1658 data
sheet shows that a higher voltage level is needed if speed is
to be increased. However, the low–pass filter inverts the sig-
nal from the phase detector (due to the active element config-
uration). Therefore, the programming of the polarity for the
phase detector means that the POL bit must be a “1.”
The R Register is programmed for a divide value that
results in the proper frequency at the phase detector refer-
ence input. In this case, 230 kHz is needed. Therefore, with
the 4.6 MHz source shown in Figure 3, the R Register needs
a value of $000014 (3 bytes, 20 in decimal).
The N Register determines the frequency tuned. Tuning
9.2 MHz requires the proper value for N to multiply up the
reference of 230 kHz to 9.2 MHz. This is 40 decimal. For
12.19 MHz, the value is 53 decimal. To tune over the range,
change the value in the N Register within the range of 40 to 53
with a 2–byte transfer. Table 1 shows the possible frequen-
cies.
Table 1. The HF Oscillator Frequencies
N Value
Frequency, MHz
40
41
42
43
44
45
46
47
48
49
50
51
52
53
9.20
9.43
9.66
9.89
10.12
10.35
10.58
10.81
11.04
11.27
11.50
11.73
11.96
12.19
EXTRA FILTERING FOR THE HF LOOP
When the HF oscillator was built, the proper frequencies
could not be tuned. The output of the MC1658 was examined
with an oscilloscope and the switching edges were discov-
ered to be “ragged.” That is, the output did not appear to be a
square wave with clean transitions.
The fin input of the MC145170 is sensitive to 500 mV p–p
signals, and the ragged edges were being amplified and
counted down by the N Counter. Therefore, the edges need-
ed cleaning up. One method would have been to add a low–
pass filter between the MC1658 and MC145170. However,
because an additional buffer was needed elsewhere in the
circuit, an MC74HCU04 inverter was used in place of the fil-
ter. This inverter’s frequency response is low enough to clean
up the ragged edges. That is, filtering of the ragged edges
occurred, and the output had smoother transitions. As men-
tioned previously, one of the elements in the inverter package
was used to buffer the output of the VCM before feeding it to
the outside world. See Figure 3.
VHF SYNTHESIZER
The MC145170 may be used in VHF designs, also. The
range for this next example is 140 to 160 MHz in 100 kHz
increments.
VHF SYNTHESIZER LOW–PASS FILTER
To illustrate design with the doubled–ended phase detec-
tor, the
φ
R and
φ
V outputs are used. This requires an opera-
tional amplifier, as shown in Figure 5. From the design
guidelines shown in the MC145170 data sheet, the following
equations are used:
ω
n =
K
φ
KVCO
N C R1
ζ
=
ω
n R2C
(1)
2
(2)
damping factor
where, from the data sheet, the equation for the
φ
R and
φ
V
phase detector,
K
φ
=VDD
2
π
2
π
(3)
5
=
= 0.796 V/rad
ζ
= 0.707,
ω
n =2
π
fR
50
(4)
2
π
x 100 kHz
50
=
= 12,566 rad/s
and
KVCO =2
π
fVCO
VVCO
(5)
2
π
x (160 – 140 MHz)
10 – 2
=
= 1.57 x 107 rad/s/V
The control voltage range on the input to the VCO is picked
to be 2 to 10 V.
The average frequency = (140 + 160)/2 = 150 MHz. There-
fore, the average N = 1500.
The above choices for
ζ
and
ω
n are rules of thumb that are
a good design starting point. A larger
ω
n value results in faster
loop lock times and higher reference frequency VCO
sidebands for similar sideband filtering. (See Advanced
Considerations.)
Choosing C1 to be 4700 pF, R1 is calculated from the
rearranged expression for
ω
n as:
R1=K
φ
KVCO
C1
ω
nN
= 11.23 k
(6)
(0.796 V/rad)(1.57 x 107 rad/s/V)
(4700 pF)(12,566 rad/s)2 (1500)
=
2
Therefore, chose an 11 k
standard value resistor.
R2 is determined from:
2
ζ
ω
nC1
R2 =
(7)
(2)(0.707)
(12,566)(4700 pF)
=
= 23.94 k
or
24 k
(standard value)
VHF SYNTHESIZER EXTRA FILTERING
For more demanding applications, extra filtering is some-
times added. This reduces the VCO sidebands caused by a
small amount of the reference frequency feeding through the
filter. One form of this filtering consists of spitting R1 into two
resistors; each resistor is one–half the value of R1, as indi-
cated by R1/2 in Figure 5. Capacitors CC are added from the
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
A
相關PDF資料 |
PDF描述 |
|---|---|
| AN1207D | THE MC145170 in Basic HF and VHF Oscillators |
| AN1241 | Interfacing the MC68HC705J1A to 9356/9366 EEPROMs |
| AN1241D | Interfacing the MC68HC705J1A to 9356/9366 EEPROMs |
| AN1432NT | AN1432NT - Variable output. low voltage operation shunt regulator |
| AN1434M | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN12073A-VB | 制造商:Panasonic Industrial Company 功能描述:IC |
| AN1207D | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:THE MC145170 in Basic HF and VHF Oscillators |
| AN1208 | 制造商:Vynckier Enclosure Systems Inc 功能描述:ENCLOSURE JUNCTION BOX POLYESTER BEIGE 制造商:VYNCKIER ENCLOSURE SYSTEMS 功能描述:ENCLOSURE, JUNCTION BOX, POLYESTER BEIGE; Enclosure Type:Junction Box; Enclosure Material:Fiberglass Reinforced Polyester; Body Color:Beige; External Height - Imperial:12.4"; External Height - Metric:315mm; IP Rating:IP66 ;RoHS Compliant: Yes |
| AN1208HNA | 制造商:Vynckier Enclosure Systems Inc 功能描述:ARIA AN1208 W/ A-HN INSTALLED |
| AN1208HPLA | 制造商:Vynckier Enclosure Systems Inc 功能描述:ARIA AN1208 W/ A-HNMPL INSTALLED |
發布緊急采購，3分鐘左右您將得到回復。