- 您現在的位置：買賣IC網 > PDF目錄378403 > AN-7820 (Fairchild Semiconductor Corporation) Circular Connector; No. of Contacts:37; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:15-35 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | AN-7820 |
| 廠商： | Fairchild Semiconductor Corporation |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:37; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:15-35 RoHS Compliant: No |
| 中文描述： | 評價委員會 |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 206K |
| 代理商： | AN-7820 |
4
5/22/97
AN7820/24
SPT7824 and 20 to 300 nsec for SPT7820. This is due to the
internal THA. When operating the SPT7820 or SPT7824
faster than 3 MSPS, keep the clock duty cycle at approxi-
mately 50%
±
10%. The probe jack PJ1 is the monitoring test
point for the CLK IN. Use this test point when adjusting the
clock duty cycle.
Logic low of the CLK IN (pin 17) causes the internal THA to
go into track. It is necessary to keep the SPT7820 or
SPT7824 in the track mode when the device is idle for an
extended period of time or at the start-up time. This setup will
prevent the internal THA from going to saturation due to the
internal THA’s droop. EB7820/24 provides a logic low to the
clock of the SPT7820/24 when the pulse generator (CLK) is
removed from the evaluation board.
TTL-OUTPUT DATA LATCHES
The rise time (Trise) and fall time (Tfall) of SPT7820/24 (D0-
D9) are not symmetrical. The propagation delay with respect
to trise (at the 2.4 V crossing) is typically 14 nsec and 6 nsec
is typical with respect to tfall (at the 2.4 V crossing). Figure
5 shows the actual output characteristic of the SPT7820/24.
This nonsymmetrical trise and tfall creates approximately
8 nsec of invalid data.
In an application where a reconstruction DAC is needed, the
above invalid data zone will cause the reconstruction signal
to have an unwanted heavy glitch if the DAC is directly
interfaced with SPT7820 or SPT7824. To avoid this, buffer
the SPT7820/24 by the edge-triggered latches. FAST family
TTL logic will fit well in this application due to its fast setup and
hold time.
U7 and U8 (74F174) are the output latches. The FAST family
TTL-logic is very sensitive to electrostatic discharge (ESD).
RN1 and RN2 are the 8 pin SIP resistor networks, 10 k
.
They protect U7 and U8 by providing the ESD path to DGND.
The BNC connector (CCLK) is the capture clock, which has
51
termination R12 on board. The outputs of the data
latches (D0-D9) are routed through the standard 26-pin
female ribbon connector (P2). SJ3-5 are the solder jumper
options for the capture clock. Only one of these jumpers
needs to be connected:
-
When SJ3 is installed (factory installed when this board is
shipped), SPT7820/24 and the latches (U7 and U8) are
clocked at the same time. With this configuration, the data
seen at the connector P2 adds another clock of latency
(two clocks of latency total as shown in figure 6).
-
When SJ4 is installed, the capture clock must be supplied
externally through CCLK. The setup time (ts) and hold
time (th) in table 5 must be met when selecting this option.
-
When SJ5 is selected, the buffers will be latched at the
falling edge of the CLK IN (SPT7820/24). With this option,
the setup time (ts) and hold time requirements for the
74F174 latches must be met (table 5). The placement of
this capture clock edge is dependent on the clock pulse
width and the sampling frequency. This option is not
recommended above 25 MSPS to avoid latching the
invalid data.
Figure 5 - Digital Output Characteristic of the SPT7820 or SPT7824
N+1
INVALID
DATA
Rise Time
≤
6nSEC
2.4V
2.4V
Invalid
Data
t
pd1
(14 nS typ.)
6nS
typ.
CLK IN
DATA OUT
(Actual)
N
(N-2)
(N-1)
(N-2)
(N-1)
Invalid
Data
(N)
INVALID
DATA
(N-1)
DATA OUT
(Equivalent)
3.5V
0.8V
0.5V
The digital outputs (latched) are routed through P2, 26 pin ribbon connector. (See table 4.)
The overrange bit (D10) could be viewed through test point TP13. D10 does not bring out through P2.
相關PDF資料 |
PDF描述 |
|---|---|
| AN-9008 | Circular Connector; No. of Contacts:37; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle RoHS Compliant: No |
| AN-902 | Twisted Pair FDDI Magnetics Overview and Recommendations |
| AN-90 | 74C Family Characteristics |
| AN-994-1 | MAXIMIZING THE EFFECTIVENESS OF YOUR SMD ASSEMBLIES |
| AN-CC1002 | Design Considerations for ISD1700 Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN7820F | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:3-pin positive output voltage regulator (1 A type) |
| AN7824 | 制造商:Panasonic Industrial Company 功能描述:IC |
| AN7824F | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:3-pin positive output voltage regulator (1 A type) |
| AN783-6 | 制造商: 功能描述: |
| AN783-6D | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。