參數資料
型號： AmMC004AWP
廠商： Advanced Micro Devices, Inc.
元件分類： 圓形連接器
英文描述： Circular Connector; No. of Contacts:6; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:8; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:8-35 RoHS Compliant: No
中文描述： 2，4，或8兆的5.0伏，只有Flash微型卡
文件頁數： 21/39頁
文件大?。?/td> 182K
代理商： AMMC004AWP
AmMC0XXA
21
P R E L IM IN A R Y
Table 14.
Embedded Program Algorithm
Figure 5.
Embedded Program Algorithm
Reset Command
The device automatically powers up in the read/reset
state. A command sequence is not required to read
data in this case. Standard microprocessor cycles re-
trieve array data. This default state ensures that no
spurious alteration of the memory content occurs dur-
ing the power transition. Refer to the AC Characteris-
tics section for the specific timing parameters.
The reset operation is initiated by writing the read/reset
command sequence into the command register. Micro-
processor read cycles retrieve array data from the
memory. The device remains enabled for reads until
the command register contents are altered.
Sector Erase Suspend
Sector Erase Suspend command allows the user to in-
terrupt the chip and then do data reads (not program)
from a non-busy sector while it is in the middle of a Sec-
tor Erase operation (which may take up to several sec-
onds). This command is applicable ONLY during the
Sector Erase operation and will be ignored if written
during the chip Erase or Programming operation. The
Erase Suspend command (B0h) will be allowed only
during the Sector Erase Operation that will include the
sector erase time-out period after the Sector Erase
commands (30h). Writing this command during the
time-out will result in immediate termination of the
time-out period. Any subsequent writes of the Sector
Erase command will be ignored as such, but instead
will be taken as the Erase Resume command. Note
that any other commands during the time out will reset
the device to read mode. The addresses are
don’t-cares in writing the Erase Suspend or Erase Re-
sume commands.
When the Sector Erase Suspend command is written
during a Sector Erase operation, the chip will take be-
tween 0.1
μ
s to 10
μ
s to suspend the erase operation
and go into erase suspended read mode (pseudo-read
mode), during which the user can read from a sector
that is NOT being erased. A read from a sector being
erased may result in invalid data. The user must moni-
tor D6 to determine if the chip has entered the pseu-
do-read mode, at which time D6 stops toggling. Note
that the user must keep track of what state the chip is
in since there is no external indication of whether the
chip is in pseudo-read mode or actual read mode. After
the user writes the Sector Erase Suspend command
and waits until D6 stops toggling, data reads from the
device may then be performed. Any further writes of
the Sector Erase Suspend command at this time will be
ignored.
To resume the operation of Sector Erase, the Resume
command (30H) should be written. Any further writes of
the Resume command at this point will be ignore.
Another Sector Erase Suspend command can be
written after the chip has resumed.
Write Operation Status
Table 15 shows the status bit states for device program
and erase operations.
Data
Polling—D7 (D15 on Odd Byte)
The AMD Flash Miniature Card features Data Polling
as a method to indicate to the host system that the
Embedded algorithms are either in progress or com-
pleted (The host may alternatively monitor BUSY#
(RY/BY#).
While the Embedded Programming algorithm is in oper-
ation, an attempt to read the device will produce the
complement of expected valid data on D7 of the
addressed memory sector or memory device. Upon
completion of the Embedded Program algorithm an
Bus
Operation
Command
Comments
Standby
Wait for V
CC
ramp
Write
Embedded Program
command sequence
3 bus cycle operation
Write
Program
Address/Data
1 bus cycle operation
Read
Data
Poll or check
BUSY# (RY/BY#) to
verify program
Write Embedded Write Command
Sequence per Tables 5– 10
Verify
Data
N
Y
Data
Poll Device
or wait for BUSY# (RY/BY#)
Y
Increment
Address
N
Start
Completed
Last
Address
20975D-6
相關PDF資料
PDF描述
AmMC008AWP Circular Connector; No. of Contacts:6; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:8; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:8-35 RoHS Compliant: No
AmMCL002AWP Circular Connector; No. of Contacts:6; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:8; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:8-6 RoHS Compliant: No
AmMCL004AWP Circular Connector; No. of Contacts:3; Series:MS27497; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:8; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:8-98 RoHS Compliant: No
AMMCL00XA JT 3C 3#20 SKT RECP
AMP-25G Plug-In Amplifier
相關代理商/技術參數
參數描述
AMMC008ANP-150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM Module
AMMC008AWP 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:2, 4, or 8 Megabyte 5.0 Volt-only Flash Miniature Card
AMMC0XXA 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:2, 4, or 8 Megabyte 5.0 Volt-only Flash Miniature Card
AMMC-2008-W10 功能描述:RF 開關 IC Switch GaAs SPDT RoHS:否 制造商:M/A-COM Technology Solutions 開關數量:Single 開關配置:SPDT 介入損耗:0.6 dB 截止隔離（典型值）:43 dB 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFN-16 封裝:Reel
AMMC-2008-W50 功能描述:RF 開關 IC Switch GaAs SPDT RoHS:否 制造商:M/A-COM Technology Solutions 開關數量:Single 開關配置:SPDT 介入損耗:0.6 dB 截止隔離（典型值）:43 dB 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*