- 您現在的位置：買賣IC網 > PDF目錄378402 > AME9001 (AME, Inc.) CCFL BACKLIGHT CONTROLLER PDF資料下載
參數資料
| 型號： | AME9001 |
| 廠商： | AME, Inc. |
| 英文描述： | CCFL BACKLIGHT CONTROLLER |
| 中文描述： | CCFL背光控制器 |
| 文件頁數： | 2/27頁 |
| 文件大小： | 370K |
| 代理商： | AME9001 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
AME, Inc.
2
CCFL Backlight Controller
AME9001
n
Pin Description
Pin #
Pin Name
Pin Description
1
VREF
Reference. Compensation point for the 3.4V internal voltage reference. Must
have bypass capacitor connected here to VSS.
Chip enable. When low (<0.4V) the chip is put into a low current (~0uA)
shutdown mode.
Blanking interval ramp. During the first cycle this pin sources 1
m
A. During
subsequent cycles it sources 150
m
A. This is primarily used to provide a
"blanking interval" at the beginning of every dimming cycle to temporarily disable
the fault protection circuitry. (See application notes.)
A resistor connected from this pin to VBATT modulates the switching frequency
as a function of battery voltage.
0.1
m
F cap to VSS.
A resistor from this pin to VSS sets the minimum frequency of the VCO. The
voltage at this pin is 1.5V
Negative supply. Connect to system ground.
Over voltage protection input. Indirectly senses the voltage at the secondary of
the transformer through a resistor (or capacitor) divider. It will immediately turn
the circuit off if the voltage at OVP is over 3V. It will also turn the chip off if the
voltage at OVP is less than 250mV for 4 successive clock cycles after the
voltage at SSC has risen above 3V (SSC>3V).
Negative input of the auxiliary error amplifier(EA2). In this application it is
normally shorted to CSCOMP
Output of the auxiliary error amplifier(EA2). In this application the auxiliary error
amp is in a unity gain configuration and the voltage at CSCOMP =1.25V as long
as SSC > 1.25V. Otherwise CSCOMP is clamped to the voltage at SSC.
Current sense detect. Connect this pin to the CCFL current sense resistor
divider. If this pin is below 250mV for 4 consecutive clock cycles after SSC > 3V
then the circuit will shutdown.
Must float.
Drives one of the external NFETs, opposite phase of OUTAPB.
Drives one of the external NFETs, opposite phase of OUTC.
Drives the high side PFET.
Battery input. This is the positive supply for the OUTA driver.
Must be tied to VDD.
Regulated 5V supply input.
Sets the dimming cycle frequency. Usually about 100Hz.
Negative input of the voltage control loop error amplifier.
Output of the voltage control loop error amplifier.
2
CE
3
SSC
4
RDELTA
5
FAULTB
6
RT2
7
VSS
8
OVP
9
CS
10
CSCOMP
11
CSDET
12
13
14
15
16
17
18
19
20
21
NC
OUTC
OUTAPB
OUTA
VBATT
VDD1
VDD
CT1
FB
COMP
22
BRIGHT
Brightness control input. A DC voltage on this controls the duty cycle of the
dimming cycle. This pin is compared to a 3V ramp at the CT1 pin.
23
SSV
Soft start ramp for the voltage control loop. (20uA source current.)
24
PNP
Drives the base of an external PNP transistor used for the 5V LDO.
相關PDF資料 |
PDF描述 |
|---|---|
| AME9001AETH | CCFL BACKLIGHT CONTROLLER |
| AME9172AAHAZ | Bus Termination Regulator |
| AME9172 | Replacement for Texas Instruments part number 54HC51/BCA. Buy from authorized manufacturer Rochester Electronics. |
| AME9172AAZAZ | Bus Termination Regulator |
| AMF2803R3D | ADVANCED ANALOG RADIATION TOLERANT DC/DC CONVERTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AME9001AETH | 制造商:AME 制造商全稱:Analog Microelectronics 功能描述:CCFL BACKLIGHT CONTROLLER |
| AME9002 | 制造商:AKM 制造商全稱:AKM 功能描述:CCFL Backlight Controller |
| AME9002AEJH | 制造商:AKM 制造商全稱:AKM 功能描述:CCFL Backlight Controller |
| AME9002AEPH | 制造商:AKM 制造商全稱:AKM 功能描述:CCFL Backlight Controller |
| AME9002AETH | 制造商:AKM 制造商全稱:AKM 功能描述:CCFL Backlight Controller |
發布緊急采購，3分鐘左右您將得到回復。