- 您現在的位置：買賣IC網 > PDF目錄366515 > AM29LV640MU90RWHI (ADVANCED MICRO DEVICES INC) 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control PDF資料下載
參數資料
| 型號： | AM29LV640MU90RWHI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| 中文描述： | 4M X 16 FLASH 3V PROM, 90 ns, PBGA63 |
| 封裝： | 12 X 11 MM, 0.80 MM PITCH, FBGA-63 |
| 文件頁數： | 36/59頁 |
| 文件大?。?/td> | 699K |
| 代理商： | AM29LV640MU90RWHI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
34
Am29LV640MU
25301C5 February1,2007
D A T A S H E E T
Figure 9.
Toggle Bit Algorithm
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indi-
cates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit
II is valid after the rising edge of the final WE# pulse in
the command sequence.
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for era-
sure. (The system may use either OE# or CE# to con-
trol the read cycles.) But DQ2 cannot distinguish
whether the sector is actively erasing or is erase-sus-
pended. DQ6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but
cannot distinguish which sectors are selected for era-
sure. Thus, both status bits are required for sector and
mode information. Refer to
Table 11
to compare out-
puts for DQ2 and DQ6.
Figure 8 shows the toggle bit algorithm in flowchart
form, and the section “DQ2: Toggle Bit II” explains the
algorithm. See also the
DQ6: Toggle Bit I
subsection.
Figure 20 shows the toggle bit timing diagram. Figure
21 shows the differences between DQ2 and DQ6 in
graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 8 for the following discussion. When-
ever the system initially begins reading toggle bit sta-
tus, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically,
the system would note and store the value of the tog-
gle bit after the first read. After the second read, the
system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the fol-
lowing read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is tog-
gling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the de-
vice did not completed the operation successfully, and
the system must write the reset command to return to
reading array data.
The remaining scenario is that the system initially de-
termines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor
the toggle bit and DQ5 through successive read cy-
cles, determining the status as described in the previ-
ous paragraph. Alternatively, it may choose to perform
START
No
Yes
Yes
DQ5 = 1
No
Yes
Toggle Bit
= Toggle
No
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Read DQ7–DQ0
Toggle Bit
= Toggle
Read DQ7–DQ0
Twice
Read DQ7–DQ0
Note:
The system should recheck the toggle bit even if
DQ5 = “1” because the toggle bit may stop toggling as DQ5
changes to “1.” See the subsections on DQ6 and DQ2 for
more information.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV640MU90WHI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU100WHI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU110PCI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU110WHI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU101PCI | 64 Megabit (4 M x 16-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV641DH120REF | 制造商:Spansion 功能描述:Flash Memory IC |
| am29lv641dh90ref | 制造商:Spansion 功能描述:IC SM FLASH 3V 64MB |
| AM29LV641DH90REF | 制造商:Spansion 功能描述:FLASH MEMORY IC |
| AM29LV641DL120RFI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV641DL-90REF | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。