- 您現在的位置：買賣IC網 > PDF目錄366484 > Am29LV160BB80WCCB (Advanced Micro Devices, Inc.) 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | Am29LV160BB80WCCB |
| 廠商： | Advanced Micro Devices, Inc. |
| 元件分類： | FLASH |
| 英文描述： | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 16Mb(2M×8位/1Mx16位), 3V, CMOS引導扇區閃存 |
| 文件頁數： | 9/46頁 |
| 文件大?。?/td> | 649K |
| 代理商： | AM29LV160BB80WCCB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
P R E L IM IN A R Y
Am29LV160B
9
Writing Commands/Command Sequences
To write a command or command sequence (which in-
cludes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to V
IL
, and OE# to V
IH
.
For program operations, the BYTE# pin determines
whether the device accepts program data in bytes
or words. Refer to “Word/Byte Configuration” for
more information.
The device features an
Unlock Bypass
mode to facili-
tate faster programming. Once the device enters the Un-
lock Bypass mode, only two write cycles are required to
program a word or byte, instead of four. The “Word/Byte
Program Command Sequence” section has details on
programming data to the device using both standard and
Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. Tables 2 and 3 indicate the
address space that each sector occupies. A “sector ad-
dress” consists of the address bits required to uniquely
select a sector. The “Command Definitions” section
has details on erasing a sector or the entire chip, or
suspending/resuming the erase operation.
After the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the “Autoselect Mode” and “Autoselect
Command Sequence” sections for more information.
I
CC2
in the DC Characteristics table represents the ac-
tive current specification for the write mode. The “AC
Characteristics” section contains timing specification
tables and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and I
CC
read specifications apply. Refer to “Write Operation
Status” for more information, and to “AC Characteris-
tics” for timing diagrams.
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at V
CC
±
0.3 V.
(Note that this is a more restricted voltage range than
V
IH
.) If CE# and RESET# are held at V
IH
, but not within
V
CC
±
0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device requires
standard access time (t
CE
) for read access when the
device is in either of these standby modes, before it is
ready to read data.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
In the DC Characteristics table, I
CC3
and I
CC4
repre-
sents the standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device
energy consumption. The device automatically
enables this mode when addresses remain stable for
t
ACC
+ 30 ns. The automatic sleep mode is
independent of the CE#, WE#, and OE# control
signals. Standard address access timings provide new
data when addresses are changed. While in sleep
mode, output data is latched and always available to
the system. I
CC4
in the DC Characteristics table
represents the automatic sleep mode current
specification.
相關PDF資料 |
PDF描述 |
|---|---|
| Am29LV160BB80RWCCB | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV160BT80RSEB | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV160BB120FIB | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV160BB80REE | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV160BB80REI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV160BT-120EI | 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 90ns 48-Pin TSOP Tray |
| AM29LV160BT80SC | 制造商:AMD 功能描述:* |
| AM29LV160BT-90EC | 制造商:Advanced Micro Devices 功能描述:NOR Flash, 1M x 16, 48 Pin, Plastic, TSSOP |
| AM29LV160BT-90FC | 制造商:Advanced Micro Devices 功能描述: 制造商:Advanced Micro Devices 功能描述:1M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| AM29LV160DB120EI | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。