亚洲无码在线视频一区二区三区,亚洲a∨国产av综合av毛片

收藏本站

您好，
買賣IC網歡迎您。
請登錄
免費注冊

您現在的位置：買賣IC網 > PDF目錄366468 > AM29LV065DU121RFEN (Advanced Micro Devices, Inc.) 64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control PDF資料下載

參數資料

型號：	AM29LV065DU121RFEN
廠商：	Advanced Micro Devices, Inc.
英文描述：	64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control
中文描述：	64兆位（8米× 8位）的CMOS 3.0伏特，只有統一部門閃光控制記憶與VersatileIOTM
文件頁數：	20/52頁
文件大小：	1184K
代理商：	AM29LV065DU121RFEN

January 10, 2002

Am29LV065D

SecSi (Secured Silicon) Sector Flash

Memory Region

The SecSi (Secured Silicon) Sector feature provides a

Flash memory region that enables permanent part

identification through an Electronic Serial Number

(ESN). The SecSi Sector is 256 bytes in length, and

uses a SecSi Sector Indicator Bit (DQ7) to indicate

whether or not the SecSi Sector is locked when

shipped from the factory. This bit is permanently set at

the factory and cannot be changed, which prevents

cloning of a factory locked part. This ensures the secu-

rity of the ESN once the product is shipped to the field.

AMD offers the device with the SecSi Sector either

factory locked or customer lockable. The fac-

tory-locked version is always protected when shipped

from the factory, and has the SecSi (Secured Silicon)

Sector Indicator Bit permanently set to a

“

”

The cus-

tomer-lockable version is shipped with the SecSi Sec-

tor unprotected, allowing customers to utilize that

sector in any manner they choose. The customer-lock-

able version also has the SecSi Sector Indicator Bit

permanently set to a

“

”

Thus, the SecSi Sector Indi-

cator Bit prevents customer-lockable devices from

being used to replace devices that are factory locked.

The SecSi sector address space in this device is allo-

cated as follows:

Table 5.

SecSi Sector Contents

The system accesses the SecSi Sector through a

command sequence (see

“

Enter SecSi Sector/Exit

SecSi Sector Command Sequence

”

). After the system

has written the Enter SecSi Sector command se-

quence, it may read the SecSi Sector by using the ad-

dresses normally occupied by the first sector (SA0).

This mode of operation continues until the system is-

sues the Exit SecSi Sector command sequence, or

until power is removed from the device. On power-up,

or following a hardware reset, the device reverts to

sending commands to sector SA0.

Factory Locked: SecSi Sector Programmed and

Protected At the Factory

In devices with an ESN, the SecSi Sector is protected

when the device is shipped from the factory. The SecSi

Sector cannot be modified in any way. A factory locked

device has an 16-byte random ESN at addresses

000000h

–

00000Fh.

Customers may opt to have their code programmed by

AMD through the AMD ExpressFlash service. The de-

vices are then shipped from AMD

’

s factory with the

SecSi Sector permanently locked. Contact an AMD

representative for details on using AMD

’

s Express-

Flash service.

Customer Lockable: SecSi Sector NOT

Programmed or Protected At the Factory

As an alternative to the factory-locked version, the de-

vice may be ordered such that the customer may pro-

gram and protect the 256-byte SecSi sector. The

SecSi Sector is one-time programmable, may not be

erased, and can be locked only once. Note that the ac-

celerated programming (ACC) and unlock bypass

functions are not available when programming the

SecSi Sector.

The SecSi Sector area can be protected using one of

the following procedures:

Write the three-cycle Enter SecSi Sector Region

command sequence, and then follow the in-system

sector protect algorithm as shown in

Figure 2

, ex-

cept that

RESET# may be at either V

or V

. This

allows in-system protection of the SecSi Sector

without raising any device pin to a high voltage.

Note that this method is only applicable to the SecSi

Sector.

Write the three-cycle Enter SecSi Sector Region

command sequence, and then use the method of

sector protection described in the

“

Sector Group

Protection and Unprotection

”

section.

The SecSi Sector is one-time programmable. Once

the SecSi Sector is programmed, locked and verified,

the system must write the Exit SecSi Sector Region

command sequence to return to reading and writing

the remainder of the array.

The SecSi Sector protection must be used with cau-

tion since, once protected, there is no procedure avail-

able for unprotecting the SecSi Sector area and none

of the bits in the SecSi Sector memory space can be

modified in any way.

Hardware Data Protection

The command sequence requirement of unlock cycles

for programming or erasing provides data protection

against inadvertent writes (refer to

Table 10

for com-

mand definitions). In addition, the following hardware

data protection measures prevent accidental erasure

or programming, which might otherwise be caused by

spurious system level signals during V

power-up

and power-down transitions, or from system noise.

Low V

Write Inhibit

When V

is less than V

LKO

, the device does not ac-

cept any write cycles. This protects data during V

power-up and power-down. The command register

and all internal program/erase circuits are disabled,

and the device resets to the read mode. Subsequent

SecSi Sector

Address Range

Standard

Factory Locked

ExpressFlash

Factory Locked

ESN or

determined by

customer

Determined by

customer

Customer

Lockable

000000h

–

00000Fh

ESN

Determined by

customer

000010h

–

00007Fh,

000400h

–

00047Fh

Unavailable

相關PDF資料	PDF描述
AM29LV065DU121RFI	64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control
AM29LV065DU121RFIN	64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control
AM29LV065DU121RWHE	64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control
AM29LV065DU121RWHEN	64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control
AM29LV065DU121RWHI	64 Megabit (8 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIOTM Control

相關代理商/技術參數	參數描述
AM29LV065DU90REF	制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 64Mbit 8M x 8bit 90ns 48-Pin TSOP 制造商:Spansion 功能描述:IC SM FLASH 3V 64MB
AM29LV065DU90REF	制造商:Spansion 功能描述:FLASH MEMORY IC
AM29LV065DU90REI	制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 64Mbit 8M x 8bit 90ns 48-Pin TSOP 制造商:Spansion 功能描述:IC, FLASH MEM, 64MBIT, 90NS, 48-TSOP, Memory Type:Flash, Memory Size:64Mbit, Mem
AM29LV065DU-90REI	制造商:Advanced Micro Devices 功能描述:NOR Flash, 8M x 8, 48 Pin, Plastic, TSSOP
AM29LV065DU90RWHF	制造商:Spansion 功能描述:

發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

添加更多采購

我的聯系方式

采購需求

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

我的聯系方式

采購需求

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

我的聯系方式

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價