- 您現在的位置：買賣IC網 > PDF目錄362259 > AM29F400T-120FC 75V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRF1407S with Lead Free Packaging PDF資料下載
參數資料
| 型號： | AM29F400T-120FC |
| 英文描述： | 75V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRF1407S with Lead Free Packaging |
| 中文描述： | x8/x16閃存EEPROM |
| 文件頁數： | 14/39頁 |
| 文件大?。?/td> | 728K |
| 代理商： | AM29F400T-120FC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
14
Am29F002B/Am29F002NB
interrupts can be re-enabled after the last Sector Erase
command is written. If the time between additional
sector erase commands can be assumed to be less
than 50 μs, the system need not monitor DQ3.
Any
command other than Sector Erase or Erase
Suspend during the time-out period resets the
device to reading array data.
The system must
rewrite the command sequence and any additional
sector addresses and commands.
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising
edge of the final WE# pulse in the command sequence.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. On the Am29F002B only, note that a
hard-
ware reset
during the sector erase operation
immediately terminates the operation. The Sector
Erase command sequence should be reinitiated once
the device has returned to reading array data, to
ensure data integrity.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the
status of the erase operation by using DQ7, DQ6, or
DQ2. Refer to “Write Operation Status” for information
on these status bits.
Figure 3 illustrates the algorithm for the erase opera-
tion. Refer to the Erase/Program Operations tables in
the “AC Characteristics” section for parameters, and to
the Sector Erase Operations Timing diagram for timing
waveforms.
Notes:
1. See the appropriate Command Definitions table for erase
command sequence.
2.
See “DQ3: Sector Erase Timer” for more information.
Figure 3.
Erase Operation
START
Write Erase
Command Sequence
Data Poll
from System
Data = FFh
No
Yes
Erasure Completed
Embedded
Erase
algorithm
in progress
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F400T-120FE | 20V Single N-Channel HEXFET Power MOSFET in a TO-262 package; A IRL3716L with Standard Packaging |
| AM29F400T-120FEB | 75V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; A IRFB3307ZPBF with Standard Packaging |
| AM29F400T-120FI | 60V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; A IRFZ44VS with Standard Packaging |
| AM29F400T-120SC | 60V Single N-Channel HEXFET Power MOSFET in a D2-Pak package; Similar to IRFZ44VS with Lead Free Packaging |
| AM29F400T-120SE | x8/x16 Flash EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F800BB-120DPC1 | 制造商:Spansion 功能描述:5V 8M FLASH KNOWN GOOD DIE W/BOTTOM BOOT (COMMERCIAL TEMP) - Gel-pak, waffle pack, wafer, diced wafer on film |
| AM29F800BB120SC | 制造商:Advanced Micro Devices 功能描述: |
| AM29F800BB-55EC | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 8Mbit 1M/512K x 8bit/16bit 55ns 48-Pin TSOP |
| AM29F800BB-55EF | 功能描述:閃存 8M (1MX8/512KX16) Parallel NOR Fl 5V RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AM29F800BB-55EF\\T | 制造商:Spansion 功能描述:IC 8MEG(512K16)BOTTOM SCTOR 100K (CS39S) |
發布緊急采購，3分鐘左右您將得到回復。