- 您現在的位置：買賣IC網 > PDF目錄366425 > AM29F040B-120JF (ADVANCED MICRO DEVICES INC) 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29F040B-120JF |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| 中文描述： | 512K X 8 FLASH 5V PROM, 120 ns, PQCC32 |
| 封裝： | LEAD FREE, PLASTIC, MO-052AE, LCC-32 |
| 文件頁數： | 11/36頁 |
| 文件大?。?/td> | 534K |
| 代理商： | AM29F040B-120JF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
November 1, 2006 21445E5
Am29F040B
9
D A T A S H E E T
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment
to automatically match a device to be programmed with
its corresponding programming algorithm. However,
the autoselect codes can also be accessed in-system
through the command register.
When using programming equipment, the autoselect
mode requires V
ID
(11.5 V to 12.5 V) on address pin
A9. Address pins A6, A1, and A0 must be as shown in
Autoselect Codes (High Voltage Method) table. In addi-
tion, when verifying sector protection, the sector
address must appear on the appropriate highest order
address bits. Refer to the corresponding Sector Ad-
dress Tables. The Command Definitions table shows
the remaining address bits that are don’t care. When all
necessary bits have been set as required, the program-
ming equipment may then read the corresponding
identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in the Command Defini-
tions table. This method does not require V
ID
. See
“Command Definitions”
for details on using the autose-
lect mode.
Table 3. Am29F040B Autoselect Codes (High Voltage Method)
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The hard-
ware sector unprotection feature re-enables both
program and erase operations in previously protected
sectors.
Sector protection/unprotection must be implemented
using programming equipment. The procedure re-
quires a high voltage (V
ID
) on address pin A9 and the
control pins. Details on this method are provided in a
supplement, publication number 19957. Contact an
AMD representative to obtain a copy of the appropriate
document.
The device is shipped with all sectors unprotected.
AMD offers the option of programming and protecting
sectors at its factory prior to shipping the device
through AMD’s ExpressFlash Service. Contact an
AMD representative for details.
It is possible to determine whether a sector is protected
or unprotected. See
“Autoselect Mode”
for details.
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to the Command Defi-
nitions table). In addition, the following hardware data
protection measures prevent accidental erasure or pro-
gramming, which might otherwise be caused by
spurious system level signals during V
CC
power-up and
power-down transitions, or from system noise.
Low V
CC
Write Inhibit
When V
CC
is less than V
LKO
, the device does not ac-
cept any write cycles. This protects data during V
CC
power-up and power-down. The command register and
all internal program/erase circuits are disabled, and the
device resets. Subsequent writes are ignored until V
CC
is greater than V
LKO
. The system must provide the
proper signals to the control pins to prevent uninten-
tional writes when V
CC
is greater than V
LKO
.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or
WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# =
V
IL
, CE# = V
IH
or WE# = V
IH
. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a
logical one.
Power-Up Write Inhibit
If WE# = CE# = V
IL
and OE# = V
IH
during power up, the
device does not accept commands on the rising edge
of WE#. The internal state machine is automatically
reset to reading array data on power-up.
Description
A18–A16
A15–A10
A9
A8–A7
A6
A5–A2
A1
A0
Identifier Code on
DQ7-DQ0
Manufacturer ID
:
AMD
X
X
V
ID
X
V
IL
X
V
IL
V
IL
01h
Device ID: Am29F040B
X
X
V
ID
X
V
IL
X
V
IL
V
IH
A4h
Sector Protection
Verification
Sector
Address
X
V
ID
X
V
IL
X
V
IH
V
IL
01h (protected)
00h (unprotected)
相關PDF資料 |
PDF描述 |
|---|---|
| AM29F040B-120JK | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120PD | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120PE | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120PF | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-120PI | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29F040B120JI | 制造商:Advanced Micro Devices 功能描述: |
| AM29F040B-120JI | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K x 8bit 120ns 32-Pin PLCC 制造商:Spansion 功能描述:IC, FLASH MEM, 4MBIT, 120NS, 32-PLCC, Memory Type:Flash - NOR, Memory Size:4Mbit |
| AM29F040B-120JK\\T | 制造商:Spansion 功能描述:FLASH MEM PARALLEL 5V 4M-BIT 512K X 8 120NS 32-PIN PLCC - Tape and Reel |
| AM29F040B-120JK\T | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K x 8bit 120ns 32-Pin PLCC T/R 制造商:Spansion 功能描述:FLASH MEM PARALLEL 5V 4M-BIT 512K X 8 120NS 32-PIN PLCC - Tape and Reel |
| AM29F040B-120JKT | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 4Mbit 512K x 8bit 120ns 32-Pin PLCC T/R |
發布緊急采購，3分鐘左右您將得到回復。