參數資料
型號: AM29F016-75FI
廠商: ADVANCED MICRO DEVICES INC
元件分類: PROM
英文描述: LM330 3-Terminal Positive Regulator; Package: TO-220; No of Pins: 3; Qty per Container: 45; Container: Rail
中文描述: 2M X 8 FLASH 5V PROM, 70 ns, PDSO48
封裝: REVERSE, TSOP-48
文件頁數: 14/36頁
文件大?。?/td> 219K
代理商: AM29F016-75FI
14
Am29F016
Program Algorithm. Writing the Erase Suspend com-
mand during the Sector Erase time-out results in imme-
diate termination of the time-out period and suspension
of the erase operation.
Any other command written during the Erase Suspend
mode will be ignored except the Erase Resume com-
mand. Writing the Erase Resume command resumes
the erase operation. The addresses are “don’t-cares”
when writing the Erase Suspend or Erase Resume
command.
When the Erase Suspend command is written during
the Sector Erase operation, the device will take a max-
imum of 15
μ
s to suspend the erase operation. When
the device has entered the erase-suspended mode, the
RY/BY output pin and the DQ7 bit will be at logic ‘1’,
and DQ6 will stop toggling. The user must use the ad-
dress of the erasing sector for reading DQ6 and DQ7 to
determine if the erase operation has been suspended.
Further writes of the Erase Suspend command are ig-
nored.
When the erase operation has been suspended, the
device defaults to the erase-suspend-read mode.
Reading data in this mode is the same as reading from
the standard read mode except that the data must be
read from sectors that have not been erase-sus-
pended. Successively reading from the erase-sus-
pended sector while the device is in the
erase-suspend-read mode will cause DQ2 to toggle.
(See the section on DQ2).
After entering the erase-suspend-read mode, the user
can program the device by writing the appropriate com-
mand sequence for Byte Program. This program mode
is known as the erase-suspend-program mode. Again,
programming in this mode is the same as programming
in the regular Byte Program mode except that the data
must be programmed to sectors that are not erase-sus-
pended. Successively reading from the erase-sus-
pended sector while the device is in the
erase-suspend-program mode will cause DQ2 to tog-
gle. The end of the erase-suspended program opera-
tion is detected by the RY/BY output pin, Data Polling
of DQ7, or by the Toggle Bit I (DQ6) which is the same
as the regular Byte Program operation. Note that DQ7
must be read from the byte program address while
DQ6 can be read from any address.
To resume the operation of Sector Erase, the Resume
command (30H) should be written. Any further writes of
the Resume command at this point will be ignored. An-
other Erase Suspend command can be written after the
chip has resumed erasing.
相關PDF資料
PDF描述
AM29F016-75SC LM3310 Step-Up PWM DC/DC Converter with Integrated Op-Amp and Gate Pulse Modulation Switch; Package: LLP; No of Pins: 24; Qty per Container: 1000; Container: Reel
AM29F016-75SCB LM3310 Step-Up PWM DC/DC Converter with Integrated Op-Amp and Gate Pulse Modulation Switch; Package: LLP; No of Pins: 24; Qty per Container: 4500; Container: Reel
AM29F016-75SI LM3311 Step-Up PWM DC/DC Converter with Integrated LDO, Op-Amp, and Gate Pulse Modulation Switch; Package: LLP; No of Pins: 24; Qty per Container: 1000; Container: Reel
AM29F016-75SIB LM3311 Step-Up PWM DC/DC Converter with Integrated LDO, Op-Amp, and Gate Pulse Modulation Switch; Package: LLP; No of Pins: 24; Qty per Container: 4500; Container: Reel
AM29F016-75FIB 16-Megabit (2,097,152 x 8-Bit) CMOS 5.0 Volt-only, Sector Erase Flash Memory
相關代理商/技術參數
參數描述
AM29F016-90EC 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel 5V 16M-Bit 2M x 8 90ns 48-Pin TSOP
AM29F016B-120DGC1 制造商:Spansion 功能描述:FLASH PARALLEL 5V 16MBIT 2MX8 120NS DIE - Gel-pak, waffle pack, wafer, diced wafer on film
AM29F016B-120DPC1 制造商:Spansion 功能描述:NOR Flash Parallel 5V 16Mbit 2M x 8bit 120ns Die
AM29F016B120EC 制造商:Advanced Micro Devices 功能描述:
AM29F016B-120EC 制造商:Advanced Micro Devices 功能描述: