- 您現在的位置：買賣IC網 > PDF目錄366380 > AM28F010-70JI (ADVANCED MICRO DEVICES INC) 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory PDF資料下載
參數資料
| 型號： | AM28F010-70JI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| 中文描述： | 128K X 8 FLASH 12V PROM, 70 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 11/35頁 |
| 文件大?。?/td> | 492K |
| 代理商： | AM28F010-70JI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Am28F010
11
FLASHERASE
ERASE SEQUENCE
Erase Setup
Erase Setup is the first of a two-cycle erase command.
It is a command-only operation that stages the device
for bulk chip erase. The array contents are not altered
with this command. 20h is written to the command reg-
ister in order to perform the Erase Setup operation.
Erase
The second two-cycle erase command initiates the
bulk erase operation. You must write the Erase com-
mand (20h) again to the register. The erase operation
begins with the rising edge of the WE# pulse. The
erase operation must be terminated by writing a new
command (Erase-verify) to the register.
This two step sequence of the Setup and Erase com-
mands helps to ensure that memory contents are not
accidentally erased. Also, chip erasure can only occur
when high voltage is applied to the V
PP
pin and all con-
trol pins are in their proper state. In absence of this high
voltage, memory contents cannot be altered. Refer to
AC Erase Characteristics and Waveforms for specific
timing parameters.
Note:
The Flash memory device must be fully
programmed to 00h data prior to erasure. This
equalizes the charge on all memory cells ensuring
reliable erasure.
Erase-Verify Command
The erase operation erases all bytes of the array
in parallel. After the erase operation, all bytes must be
sequentially verified. The Erase-verify operation is initi-
ated by writing A0h to the register. The byte address to
be verified must be supplied with the command. Ad-
dresses are latched on the falling edge of the WE#
pulse or CE# pulse, whichever occurs later. The rising
edge of the WE# pulse terminates the erase operation.
Margin Verify
During the Erase-verify operation, the device applies
an internally generated margin voltage to the
addressed byte. Reading FFh from the addressed byte
indicates that all bits in the byte are properly erased.
Verify Next Address
You must write the Erase-verify command with the ap-
propriate address to the register prior to verification of
each address. Each new address is latched on the fall-
ing edge of WE# or CE# pulse, whichever occurs later.
The process continues for each byte in the memory
array until a byte does not return FFh data or all the
bytes in the array are accessed and verified.
If an address is not verified to FFh data, the entire chip
is erased again (refer to Erase Setup/Erase). Erase
verification then resumes at the address that failed to
verify. Erase is complete when all bytes in the array
have been verified. The device is now ready to be pro-
grammed. At this point, the verification operation is ter-
minated by writing a valid command (e.g. Program
Setup) to the command register. Figure 1 and Table 4,
the Flasherase
electrical erase algorithm, illustrate how
commands and bus operations are combined to per-
form electrical erasure. Refer to AC Erase Characteris-
tics and Waveforms for specific timing parameters.
相關PDF資料 |
PDF描述 |
|---|---|
| AM28F010-70JIB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PC | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PCB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PE | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PEB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM28F010-70JIB | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PC | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PCB | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PE | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-70PEB | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。