- 您現在的位置：買賣IC網 > PDF目錄166205 > ALD4704B (Advanced Linear Devices, Inc.) QUAD RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | ALD4704B |
| 廠商： | Advanced Linear Devices, Inc. |
| 元件分類： | 運算放大器 |
| 英文描述： | QUAD RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| 中文描述： | 四軌至軌CMOS運算放大器 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 62K |
| 代理商： | ALD4704B |
ALD4704A/ALD4704B
Advanced Linear Devices
4
ALD4704
TYPICAL PERFORMANCE CHARACTERISTICS
Design & Operating Notes:
1. The ALD4704 CMOS operational amplifier uses a 3 gain stage
architecture and an improved frequency compensation scheme to
achieve large voltage gain, high output driving capability, and better
frequency stability. The ALD4704 is internally compensated for unity
gain stability using a novel scheme. This design produces a clean
single pole roll off in the gain characteristics while providing for more
than 70 degrees of phase margin at the unity gain frequency. A unity
gain buffer using the ALD4704 will typically drive 400pF of external
load capacitance without stability problems. In the inverting unity gain
configuration, it can drive up to 800pF of load capacitance. Compared
to other CMOS operational amplifiers, the ALD4704 is much more
resistant to parasitic oscillations.
2. The ALD4704 has complementary p-channel and n-channel input
differential stages connected in parallel to accomplish rail to rail input
common mode voltage range. With the common mode input voltage
close to the power supplies, one of the two differential stages is
switched off internally. To maintain compatibility with other opera-
tional amplifiers, this switching point has been selected to be about
1.5V above the negative supply voltage. As offset voltage trimming on
the ALD4704 is made when the input voltage is symmetrical to the
supply voltages, this internal switching does not affect a large variety
of applications such as an inverting amplifier or non-inverting amplifier
with a gain greater than 2.5 (5V operation), where the common mode
voltage does not make excursions below this switching point.
3. The input bias and offset currents are essentially input protection diode
reverse bias leakage currents, and are typically less than 1pA at room
temperature. This low input bias current assures that the analog signal
from the source will not be distorted by input bias currents. For
applications where source impedance is very high, it may be neces-
sary to limit noise and hum pickup through proper shielding.
4. The output stage consists of class AB complementary output drivers,
capable of driving a low resistance load. The output voltage swing is
limited by the drain to source on-resistance of the output transistors as
determined by the bias circuitry, and the value of the load resistor
when connected. In the voltage follower configuration, the oscillation
resistant feature, combined with the rail to rail input and output feature,
makes the ALD4704 an effective analog signal buffer for medium to
high source impedance sensors, transducers, and other circuit net-
works.
5. The ALD4704 operational amplifier has been designed with static
discharge protection and to minimize latch up. However, care must be
exercised when handling the device to avoid strong static fields. In
using the operational amplifier, the user is advised to power up the
circuit before, or simultaneously with, any input voltages applied and
to limit input voltages to not exceed 0.3V of the power supply voltage
levels. Alternatively, a 100K
or higher value resistor at the input
terminals will limit input currents to acceptable levels while causing
very small or negligible accuracy effects.
OPEN LOOP VOLTAGE GAIN AS A FUNCTION
OF SUPPLY VOLTAGE AND TEMPERATURE
SUPPLY VOLTAGE (V)
1000
100
10
1
OPEN
LOOP
VOLTAGE
GAIN
(V/mV)
0
±2
±4
±6
RL= 10K
RL= 5K
} -55
°C
} +25
°C
} +125
°C
±8
INPUT BIAS CURRENT AS A FUNCTION
OF AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (
°C)
1000
100
10
0.1
1.0
INPUT
BIAS
CURRENT
(pA)
100
-25
0
75
125
50
25
-50
VS = ±5.0V
10000
SUPPLY CURRENT AS A FUNCTION
OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
0
SUPPLY
CURRENT
(mA)
0
±1
±2
±3
±4
±5
±6
+80
°C
+25
°C
TA = -55°C
-25
°C
±7
2
4
6
8
10
12
14
16
INPUTS GROUNDED
OUTPUT UNLOADED
+125
°C
COMMON MODE INPUT VOLTAGE RANGE
AS A FUNCTION OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
COMMON
MODE
INPUT
VOLTAGE
RANGE
(V)
±7
±6
±5
±4
±3
±2
±3
±4
±5
±6
±7
TA = 25°C
相關PDF資料 |
PDF描述 |
|---|---|
| ALD4706 | QUAD ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD4706A | QUAD ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD4706B | QUAD ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD500AUSC | PRECISION INTEGRATING ANALOG PROCESSOR |
| ALD500AUSWC | PRECISION INTEGRATING ANALOG PROCESSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ALD4704BDB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Operational Amplifier |
| ALD4704BPB | 功能描述:運算放大器 - 運放 High Slew Rate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ALD4704BPBL | 功能描述:運算放大器 - 運放 2.0mV High Slew Rate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ALD4704BSB | 功能描述:運算放大器 - 運放 High Slew Rate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ALD4704BSBL | 功能描述:運算放大器 - 運放 2.0mV High Slew Rate RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。