參數資料
型號: ALD20Y48-S
英文描述: Single Output 16th Brick: 60Watts
中文描述: 單輸出16日磚:60Watts
文件頁數: 7/20頁
文件大?。?/td> 605K
代理商: ALD20Y48-S
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16
th
Brick)
MODEL: ALD12/18/20/25 SERIES
AUGUST 17, 2005 – REVISION C
SHEET 7 OF 20
Basic Operation and Features
(continued)
OUTPUT ENABLE
(continued)
For Positive Enable, the converter is turned on when the Enable pin is at logic HIGH or left open. The unit turns off when the
Enable pin is at logic LOW or directly connected to -V
IN
. On the other hand, the Negative Enable version turns unit on when the
Enable pin is at logic LOW or directly connected to -V
IN
. The unit turns off when the Enable pin is at Logic HIGH.
OUTPUT OVER VOLTAGE PROTECTION (OVP)
The Over Voltage Protection circuit is non-latching - auto recovery mode. The converter will shut down and attempt to restart until
the fault is removed. There is a 20-50ms lockout period between restart attempts.
OVER CURRENT PROTECTION (OCP)
The Over Current Protection is non-latching - auto recovery mode. The converter shuts down once the output current reaches the
OCP range. The converter will attempt to restart until the fault is removed. There is a 20-50ms lockout period between restart
attempts. Note that the OCP threshold will be reduced proportionally with the output voltage trim up and/or remote sense
compensation. The percent rise in output voltage will be proportional to the reduction in OCP current inception.
OVER TEMPERATURE PROTECTION (OTP)
The Over Temperature Protection circuit will shutdown the converter once the average PCB temperature (See Figure 43A for OTP
reference sense point) reaches the OTP range. This feature prevents the unit from overheating and consequently going into thermal
runaway, which may further damage the converter and the end system. Such overheating may be an effect of operation outside the
given power thermal derating conditions. Restart is possible once the temperature of the sensed location drops to less than 110
°
C.
REMOTE SENSE
The remote sense pins can be used to compensate for any voltage drops (per indicated max limits) that may occur along the
connection between the output pins to the load. Pin 7 (+Sense) and Pin 5 (-Sense) should be connected to Pin 8 (+Vout) and Pin 4
(-Vout) respectively at the point where regulation is desired. The combination of remote sense and trim adjust cannot exceed 110%
of V
O
. When output voltage is trimmed up (through remote sensing and/or trim pin), output current must be derated and maximum
output power must not be exceeded.
Figure 5. Typical Application Circuit
+Vin
-Vin
+Vo
-Vo
L
O
A
D
TO SOURCE
33uF
0.1uF
10uF
相關PDF資料
PDF描述
ALD25A48- Single Output 16th Brick: 60Watts
ALD25A48-6 Single Output 16th Brick: 60Watts
ALD25A48-6S Single Output 16th Brick: 60Watts
ALD25A48N- Single Output 16th Brick: 60Watts
ALD25A48N-6 Single Output 16th Brick: 60Watts
相關代理商/技術參數
參數描述
ALD210800 制造商:ALD 制造商全稱:Advanced Linear Devices 功能描述:PRECISION N-CHANNEL EPAD MOSFET ARRAY QUAD HIGH DRIVE ZERO THRESHOLD MATCHED PAIR
ALD210800A 制造商:ALD 制造商全稱:Advanced Linear Devices 功能描述:PRECISION N-CHANNEL EPAD MOSFET ARRAY QUAD HIGH DRIVE ZERO THRESHOLD MATCHED PAIR
ALD210800APCL 功能描述:MOSFET PREC N-CHAN EPAD CMOS MOSFET ARRAY RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS(導通):0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube
ALD210800ASCL 功能描述:MOSFET PREC N-CHAN EPAD CMOS MOSFET ARRAY RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS(導通):0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube
ALD210800PCL 功能描述:MOSFET PREC N-CHAN EPAD CMOS MOSFET ARRAY RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS(導通):0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube