參數資料
型號： ALD18M48N
元件分類： 電源模塊
英文描述： 1-OUTPUT 38 W DC-DC REG PWR SUPPLY MODULE
封裝： SIXTEENTH BRICK PACKAGE-8
文件頁數： 18/20頁
文件大小： 602K
代理商： ALD18M48N
Technical Reference Notes
ALD12/18/20/25 Series
(Single Output 16
th Brick)
MODEL: ALD12/18/20/25 SERIES
SHEET 7 OF 20
AUGUST 17, 2005 – REVISION C
Basic Operation and Features (continued)
OUTPUT ENABLE (continued)
For Positive Enable, the converter is turned on when the Enable pin is at logic HIGH or left open. The unit turns off when the
Enable pin is at logic LOW or directly connected to -VIN. On the other hand, the Negative Enable version turns unit on when the
Enable pin is at logic LOW or directly connected to -VIN. The unit turns off when the Enable pin is at Logic HIGH.
OUTPUT OVER VOLTAGE PROTECTION (OVP)
The Over Voltage Protection circuit is non-latching - auto recovery mode. The converter will shut down and attempt to restart until
the fault is removed. There is a 20-50ms lockout period between restart attempts.
OVER CURRENT PROTECTION (OCP)
The Over Current Protection is non-latching - auto recovery mode. The converter shuts down once the output current reaches the
OCP range. The converter will attempt to restart until the fault is removed. There is a 20-50ms lockout period between restart
attempts. Note that the OCP threshold will be reduced proportionally with the output voltage trim up and/or remote sense
compensation. The percent rise in output voltage will be proportional to the reduction in OCP current inception.
OVER TEMPERATURE PROTECTION (OTP)
The Over Temperature Protection circuit will shutdown the converter once the average PCB temperature (See Figure 43A for OTP
reference sense point) reaches the OTP range. This feature prevents the unit from overheating and consequently going into thermal
runaway, which may further damage the converter and the end system. Such overheating may be an effect of operation outside the
given power thermal derating conditions. Restart is possible once the temperature of the sensed location drops to less than 110
°C.
REMOTE SENSE
The remote sense pins can be used to compensate for any voltage drops (per indicated max limits) that may occur along the
connection between the output pins to the load. Pin 7 (+Sense) and Pin 5 (-Sense) should be connected to Pin 8 (+Vout) and Pin 4
(-Vout) respectively at the point where regulation is desired. The combination of remote sense and trim adjust cannot exceed 110%
of VO. When output voltage is trimmed up (through remote sensing and/or trim pin), output current must be derated and maximum
output power must not be exceeded.
Figure 5. Typical Application Circuit
+Vin
-Vin
+Vo
-Vo
L
O
A
D
TO SOURCE
33uF
0.1uF
10uF
相關PDF資料
PDF描述
ALD18Y48N-S 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE
ALD25G48N 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE
ALD25Y48-6 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE
ALD12Y48N-6 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE
ALD18G48-S 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
ALD18M48N- 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Single Output 16th Brick: 60Watts
ALD18M48N-6 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Single Output 16th Brick: 60Watts
ALD18M48N-6S 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Single Output 16th Brick: 60Watts
ALD18M48N-S 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Single Output 16th Brick: 60Watts
ALD18M48-S 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Single Output 16th Brick: 60Watts
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*