- 您現在的位置：買賣IC網 > PDF目錄376482 > AIC3843CSTR (Analog Integrations Corporation) Current-Mode PWM Controller PDF資料下載
參數資料
| 型號： | AIC3843CSTR |
| 廠商： | Analog Integrations Corporation |
| 英文描述： | Current-Mode PWM Controller |
| 中文描述： | 電流模式PWM控制器 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 189K |
| 代理商： | AIC3843CSTR |
AIC3843
9
n
PIN DESCRIPTIONS
PIN 1: COMP
- This pin is the error amplifier
output and is made available
for loop compensation.
PIN 2:
VFB
- This is the inverting input of
the
error
amplifier.
normally connected to the
switching power supply output
through a resistor divider.
It
is
PIN 3:
ISENSE - A
voltage
proportional
to
inductor current is connected
to this input. The PWM uses
this information to terminate
the output switch conduction.
PIN 4:
RT/CT
- The oscillator frequency and
maximum output duty cycle
are programmed by connect-
ing resistor R
T
to V
REF
and
capacitor C
T
to ground. It is
feasible to operate when f
500KHz.
PIN 5:
GND - This pin is the combined control
circuitry and power ground.
PIN 6:
OUTPUT- This output directly drives the
gate of a power MOSFET.
Peak currents up to 1A are
sourced and sunk by this pin.
PIN 7:
VCC - This pin is the positive supply of
the control IC.
PIN 8:
VREF - This is the reference output. It
provides charging current for
capacitor CT through resistor
RT.
n
APPLICATION INFORMATIONS
Under voltage Lockout
There are two separate under voltage lockout
comparators incorporated to make sure that the
IC is fully functional before the output stage is
enabled. One is for power supply voltage (VCC)
and the other is for reference output voltage
(VREF). Each has a built in hysteresis to prevent
erratic output behavior when their respective
thresholds are crossed. For VCC comparator the
upper and lower thresholds are 8.4V and 7.6V,
respectively. The large hysteresis and low start up
current (0.3mA) of the AIC3843 make it ideally
suited in off-line converter applications where
efficient bootstrap startup techniques are required.
A 34V zener is connected as a shunt regulator
from VCC to ground. Its purpose is to protect the
IC from excessive voltage that can occur during
system start-up.
Reference Output
The 5.0V reference output is trimmed to
±
2.0%
tolerance at T
A
=25
°
C. It supplies charging current
to the oscillator timing capacitor and is capable of
providing current in excess of 20mA for powering
additional control system circuitry. In case of
overload, the reference is short-circuit protected at
相關PDF資料 |
PDF描述 |
|---|---|
| AIC812-40PVBG | Reset Circuits with Manual Reset Input |
| AIC812-40PVTR | Reset Circuits with Manual Reset Input |
| AIC812-31PVBG | Reset Circuits with Manual Reset Input |
| AIC812-31PVTR | Reset Circuits with Manual Reset Input |
| AIC812-23PVBG | Reset Circuits with Manual Reset Input |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AIC-3P-025-150 | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:High Energy Storage Chokes for inverter Applications |
| AIC-3P-032-75 | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:High Energy Storage Chokes for inverter Applications |
| AIC-3P-050-150 | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:High Energy Storage Chokes for inverter Applications |
| AIC-3P-075-30 | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:High Energy Storage Chokes for inverter Applications |
| AIC-3P-075-36 | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:High Energy Storage Chokes for inverter Applications |
發布緊急采購，3分鐘左右您將得到回復。