- 您現在的位置：買賣IC網 > PDF目錄375276 > AIC1620COTR (Analog Integrations Corporation) High Efficiency Synchronous Step-Up DC/DC Converter PDF資料下載
參數資料
| 型號： | AIC1620COTR |
| 廠商： | Analog Integrations Corporation |
| 英文描述： | High Efficiency Synchronous Step-Up DC/DC Converter |
| 中文描述： | 高效率同步降壓型DC / DC轉換器 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 456K |
| 代理商： | AIC1620COTR |
AIC1620/AIC1621/AIC1622
10
Component Selection
1. Inductor Selection
An inductor value of 22
μ
H performs well in most
applications. The AIC1620 series also work with
inductors in the 10
μ
H to 47
μ
H range. An inductor
with higher peak inductor current tends a higher
output voltage ripple (I
PEAK
ESR). The inductor’s DC resistance significantly
affects efficiency. We can calculate the maximum
output current as follows:
=
I
V
OUT
output filter capacitor
η
×
L
2
V
V
t
V
I
IN
OUT
OFF
LIM
IN
)
MAX
(
OUT
where I
OUT(MAX)
=maximum output current in
amps
V
IN
=input voltage
L=inductor value in
μ
H
=efficiency (typically 0.9)
t
OFF
=LX switch’ off-time in
μ
S
I
LIM
=0.45A or 0.8A
2. Capacitor Selection
The output voltage ripple relates with the peak in-
ductor current and the output capacitor ESR. Be-
sides output ripple voltage, the output ripple cur-
rent also needs to be concerned. The smaller the
capacitor ESR is, the higher the ripple current will
be. A filter capacitor with low ESR is helpful to
the efficiency and steady state output current of
AIC1620 series. Therefore HERMEI capacitor LT
series with 220
μ
F/6.3V is recommended. A
smaller capacitor (down to 10F with higher ESR)
is acceptable for light loads or in applications that
can tolerate higher output ripple.
3. PCB Layout and Grounding
Since AIC1622’s switching frequency can range
up to 500kHz, it makes AIC1622 become very
sensitive. So careful printed circuit layout is im-
portant for minimizing ground bounce and noise.
IC’s OUT pin should be as clear as possible. And
the GND pin should be placed close to the ground
plane. Keep the IC’s GND pin and the ground
leads of the input and output filter capacitors less
than 0.2in (5mm) apart. In addition, keep all con-
nection to the FB and LX pins as short as possi-
ble. In particular, when using external feedback
resistors, locate them as close to the FB as pos-
sible. To maximize output power and efficiency
and minimize output ripple voltage, use a ground
plane and solder the IC’s GND directly to the
ground plane. Following are the recommended
layout diagrams.
Figure 12. Top layer
Figure 13. Bottom layer
Figure 14. Placement
相關PDF資料 |
PDF描述 |
|---|---|
| AIC1621 | High Efficiency Synchronous Step-Up DC/DC Converter |
| AIC1621COTR | High Efficiency Synchronous Step-Up DC/DC Converter |
| AIC1622COTR | High Efficiency Synchronous Step-Up DC/DC Converter |
| AIC1631-3CN | 2-Cell, 500mA, Step-Up DC/DC Converter |
| AIC1631-3CS | 2-Cell, 500mA, Step-Up DC/DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AIC16-20P | 制造商:Amphenol Corporation 功能描述:CIRCULAR CONTACT, PIN, 22-20AWG, CRIMP, Series:AIC, For Use With:AIT/MS Series C |
| AIC16-20PG | 制造商:Amphenol Corporation 功能描述:ER CON 16 (20-22) PIN CRMP GLD |
| AIC16-20SG | 制造商:Amphenol Corporation 功能描述:ER CON 16 20/22 SKT AU |
| AIC1621 | 制造商:AIC 制造商全稱:Analog Intergrations Corporation 功能描述:High Efficiency Synchronous Step-Up DC/DC Converter |
| AIC1621COTR | 制造商:AIC 制造商全稱:Analog Intergrations Corporation 功能描述:High Efficiency Synchronous Step-Up DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。