- 您現在的位置：買賣IC網 > PDF目錄375273 > AH211 (BCD Semiconductor Manufacturing Limited) TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT PDF資料下載
參數資料
| 型號： | AH211 |
| 廠商： | BCD Semiconductor Manufacturing Limited |
| 英文描述： | TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT |
| 中文描述： | 兩相霍爾效應鎖存蛋白原輸出 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 202K |
| 代理商： | AH211 |
TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT AH211
9
Mar. 2007 Rev. 1.3
BCD Semiconductor Manufacturing Limited
Data Sheet
Application Information
Figure 13 is the typical application circuit for AH211.
Usually, there are three wires for fan connection: the
red is input of power supply; the yellow is the output of
FG; the black is the ground. R1 is an external pull-up
resister for the use of measuring FG signal from fan.
The value of R1 could be decided by the transistor
saturation voltage (V
ON
), sink current (I
FG
), and pull-
up voltage (V
DD
). The calculation formula is:
R1=(V
DD
-V
ON
) / I
FG
For example:
V
DD
=5V for TTL level.
If saturation voltage is 0.6V (IC specification)
I
FG
=20mA (
≤
20mA) , then R1=220
;
If saturation voltage is 0.1V, I
FG
=1mA (=<20mA) , the
value of R1=4.9k
According AH211's specification, if V
DD
=5V, R1 must
be larger than 220
.
D1 is the reverse protection diode. If the red and black
wires reversely connected, the current will flow from
the ground via IC and coils L1 and L2 to power supply.
Under such circumstances, the IC and coils are easy to
be burned out. Therefore, the reverse protection diode
D1is necessary. However, D1 will also cause an extra
voltage drop on the supply voltage.
C1 is a capacitor to reduce the ripple noise caused by
the transient of the output stages. The amplitude of the
ripple noise depends on the coil impedance and its
characteristics.
AH211
FG
DO
DOB GND
1
2
3
4
COIL1
COIL2
C1
D1
R1 1k
V
CC
(Red Wire)
V
DD
FG (Yellow Wire)
GND (Black Wire)
Figure 13. AH211 Typical Application Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| AH211Z4-AE1 | TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT |
| AH211Z4-BE1 | TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT |
| AH266_07 | HIGH VOLTAGE HALL EFFECT LATCH |
| AH266 | HIGH VOLTAGE HALL EFFECT LATCH |
| AH266Z4-AE1 | HIGH VOLTAGE HALL EFFECT LATCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AH21-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| AH2114CG | 制造商:Texas Instruments 功能描述:AH2114CG |
| AH211Z4-AE1 | 制造商:BCDSEMI 制造商全稱:BCD Semiconductor Manufacturing Limited 功能描述:TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT |
| AH211Z4-AG1 | 功能描述:IC HALL SWITCH 制造商:diodes incorporated 系列:- 包裝:散裝 零件狀態:有效 功能:卡銷 技術:霍爾效應 極化:南極 感應范圍:6mT 跳閘，-6mT 釋放 測試條件:25°C 電壓 - 電源:3.5 V ~ 16 V 電流 - 電源（最大值）:8mA 電流 - 輸出（最大值）:400mA 輸出類型:開路集電極 特性:溫度補償 工作溫度:-20°C ~ 85°C（TA） 封裝/外殼:4-SIP 供應商器件封裝:TO-94 標準包裝:1,000 |
| AH211Z4-BE1 | 制造商:BCDSEMI 制造商全稱:BCD Semiconductor Manufacturing Limited 功能描述:TWO PHASE HALL EFFECT LATCH WITH FG OUTPUT |
發布緊急采購，3分鐘左右您將得到回復。