- 您現在的位置：買賣IC網 > PDF目錄223321 > AFBR-57J5APZ FIBER OPTIC TRANSCEIVER, 830-860nm, 24576Mbps(Tx), 24576Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | AFBR-57J5APZ |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 830-860nm, 24576Mbps(Tx), 24576Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| 封裝： | ROHS COMPLIANT PACKAGE-20 |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 578K |
| 代理商： | AFBR-57J5APZ |
6
Table 2. Pin Description
Pin
Name
Function/Description
Notes
1
VeeT
Transmitter Ground
2
TX_FAULT
Transmitter Fault Indication – High indicates a fault condition
Note 1
3
TX_DISABLE
Transmitter Disable – Module optical output disables on high or open
Note 2
4
MOD-DEF2
Module Definition 2 – Two wire serial ID interface data line (SDA)
Note 3
5
MOD-DEF1
Module Definition 1 – Two wire serial ID interface clock line (SCL)
Note 3
6
MOD-DEF0
Module Definition 0 – Grounded in module (module present indicator)
Note 3
7
no connect
8
RX_LOS
Loss of Signal – High indicates loss of received optical signal
Note 4
9
VeeR
Receiver Ground
10
VeeR
Receiver Ground
11
VeeR
Receiver Ground
12
RD-
Inverse Received Data Out
Note 5
13
RD+
Received Data Out
Note 5
14
VeeR
Receiver Ground
15
VccR
Receiver Power + 3.3 V
Note 6
16
VccT
Transmitter Power + 3.3 V
Note 6
17
VeeT
Transmitter Ground
18
TD+
Transmitter Data In
Note 7
19
TD-
Inverse Transmitter Data In
Note 7
20
VeeT
Transmitter Ground
Notes:
1. TX_FAULT is an open collector/drain output, which must be pulled up with a 4.7k – 10k
resistor on the host board. When high, this output
indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
2. TX_DISABLE is an input that is used to shut down the transmitter optical output. It is internally pulled up (within the transceiver) with a 6.8k
resistor.
Low (0 – 0.8V):
Transmitter on
Between (0.8V and 2.0V):
Undefined
High (2.0 – Vcc max) or OPEN:
Transmitter Disabled
3. The signals Mod-Def 0, 1, 2 designate the two wire serial interface pins. They must be pulled up with a 4.7k – 10k
resistor on the host board.
Mod-Def 0 is grounded by the module to indicate the module is present
Mod-Def 1 is serial clock line (SCL) of two wire serial interface
Mod-Def 2 is serial data line (SDA) of two wire serial interface
4. RX_LOS (Rx Loss of Signal) is an open collector/drain output that must be pulled up with a 4.7k – 10k
resistor on the host board. When high,
this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates
normal operation. In the low state, the output will be pulled to < 0.8V.
5. RD-/+ designate the differential receiver outputs. They are AC coupled 100
differential lines which should be terminated with 100 differential
at the host SERDES input. AC coupling is done inside the transceiver and is not required on the host board. The voltage swing on these lines will
be between 500 and 1600 mV differential (250 – 800 mV single ended) when properly terminated.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined at the SFP connector pin. The maximum supply current is 300
mA and the associated in-rush current will typically be no more than 30 mA above steady state after 500 nanoseconds.
7. TD-/+ designate the differential transmitter inputs. They are AC coupled differential lines with 100
differential termination inside the module.
The AC coupling is done inside the module and is not required on the host board. The inputs will accept differential swings of 400 – 2400 mV
(200 – 1200 mV single ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single ended) be
used for best EMI performance.
相關PDF資料 |
PDF描述 |
|---|---|
| AFBR-57R5AEZ | FIBER OPTIC TRANSCEIVER, 830-860nm, 4250Mbps(Tx), 4250Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| AFBR-5803AQZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 155Mbps(Tx), 155Mbps(Rx), BOARD/PANEL MOUNT, SIP, SC CONNECTOR |
| AFBR-5803ATQZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 155Mbps(Tx), 155Mbps(Rx), BOARD/PANEL MOUNT, SIP, ST CONNECTOR |
| AFBR-5803TZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 125Mbps(Tx), 125Mbps(Rx), THROUGH HOLE MOUNT, ST CONNECTOR |
| AFBR-5903EZ | FIBER OPTIC TRANSCEIVER, 1270-1380nm, 125Mbps(Tx), 125Mbps(Rx), BOARD/PANEL MOUNT, MT-RJ CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AFBR-57J5APZ_13 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:Digital Diagnostic SFP, 850nm 3.072/2.4576 Gb/s, RoHS OBSAI/CPRI Compatible Optical Transceiver |
| AFBR-57J5APZ-AX1 | 制造商:Avago Technologies 功能描述:3G MM BASE TRANSCEIVER STATION (BTS) SFP WITH DIGITAL DIAGNO - Trays |
| AFBR-57J7APZ | 功能描述:光纖發射器、接收器、收發器 7.37/6.14 Gb/s MMF SFP, Ind Temp RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| AFBR-57J9AMZ | 制造商:Avago Technologies 功能描述:SFP+ 850NM 6GBE SR MMF, GEN 4 - Bulk 制造商:Avago Technologies 功能描述:TXRX MMF SFP 850NM 6GBE 制造商:Avago Technologies 功能描述:SFP+ 850nm 6GbE SR MMF, Gen 4 |
| AFBR-57L5APZ | 功能描述:光纖發射器、接收器、收發器 Transceiver RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。