- 您現在的位置：買賣IC網 > PDF目錄294979 > AEV19024 POWER/SIGNAL RELAY, SPST, MOMENTARY, 1.85A (COIL), 24VDC (COIL), 45000mW (COIL), 300A (CONTACT), 400VDC (CONTACT), PANEL MOUNT PDF資料下載
參數資料
| 型號： | AEV19024 |
| 元件分類： | 功率/信號繼電器 |
| 英文描述： | POWER/SIGNAL RELAY, SPST, MOMENTARY, 1.85A (COIL), 24VDC (COIL), 45000mW (COIL), 300A (CONTACT), 400VDC (CONTACT), PANEL MOUNT |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 8/8頁 |
| 文件大小： | 179K |
| 代理商： | AEV19024 |
EV (AEV)
NOTES
1. For general cautions for use, please
refer to the “General Application
Guidelines”.
2. When installing the relay, always
use washers to prevent the screws
from loosening.
Tighten each screw within the rated
range given below. Exceeding the
maximum torque may result in breakage.
Mounting is possible in either direction.
<Relay installing section>
M4 screw (for 10A type): 1.8 to 2.7 Nm
M5 screw (for 20A, 80A, 120A and 300A
types): 3 to 4 Nm
<Main terminal installing section>
M5 nut (for 80A type): 3 to 4 Nm
M6 nut (for 120A type): 6 to 8 Nm
M8 nut (for 300A type): 10 to 12 Nm
3. The coils (300 A type) and contacts
(all type) of the relay are polarized, so
follow the connection schematic when
connecting the coils and contacts.
Type 300 A contains a reverse surge
voltage absorption circuit; therefore a
surge protector is not needed. We
recommend installing a surge protector
varistor (ZNR) for the 10A, 20A, 80A and
120A types.
<Recommend varistor>
Amount of proof energy: Min. 1 J
Varistor voltage: 1.5 to 2.0 times of
nominal voltage
Avoid using a diode as this may result in
decreased cut-off capability.
4. As a general rule, do not use a relay
if it has been dropped.
5. Avoid mounting the relay in strong
magnetic elds (near a transformer or
magnet) or close to an object that
radiates heat.
6. Electrical life
This relay is a high-voltage direct-current
switch. In its nal breakdown mode, it
may lose the ability to provide the proper
cut-off. Therefore, do not exceed the
indicated switching capacity and life.
(Please treat the relay as a product with
limited life and replace it when
necessary.)
In the event that the relay loses cut-off
ability, there is a possibility that burning
may spread to surrounding parts, so
congure the layout so that the power is
turned off within one second.
7. Permeation life of internal gas
This relay uses a hermetically encased
contact (capsule contact) with gas inside.
The gas has a permeation life that is
affected by the temperature inside the
capsule contact (ambient temperature +
temperature rise due to ow of electrical
current). For this reason, make sure the
ambient operating temperature is
between –40 and 80
°C –40 and +176°F
(300A type is Max. 85
°C 185°F), and the
ambient storage temperature is between
–40 and 85
°C –40 and +185°F.
8. If the power is turned off and then
immediately on after applying the
rated voltage (current) continuously to
the relay’s coil and contact, the
resistance of the coil will increase due
to a rise in the coil temperature.
This causes the pick-up voltage to
rise, and possibly exceed the rated
pick-up voltage. In these
circumstances, take measures such
as reducing the load current, limiting
the duration of current ow, and
applying a coil voltage higher than the
rated operating voltage.
9. Main contact ratings in the ratings
apply to when there is a resistive load.
If you are using an inductive load
(L load) such that L/R > 1 ms, add
surge protection in parallel with the
inductive load.
If this is not done, the electrical life
will decrease and cut-off failure may
occur.
10. For the 300 A type, drive the coil
with a quick startup.
(Built-in one-shot pulse generator
circuit)
11. Be careful that foreign matter and
oils and fats kind don’t stick to the
main terminal parts because it is likely
to cause terminal parts to give off
unusual heat.
Also, please use the following
materials for connected harnesses
and bus bars.
10A type: Min. 2 mm2 nominal cross-
sectional area
20A type: Min. 3 mm2 nominal cross-
sectional area
80A type: Min. 15 mm2 nominal cross-
sectional area
120A type: Min. 38 mm2 nominal cross-
sectional area
300A type: Min. 100 mm2 nominal cross-
sectional area
12. As a guide, the insertion strength
of the plug-in terminal into the relay
tab terminal should be 40 to 70N (10A
type), 40 to 80N (20A type). Please
select a plug-in terminal (at
connection terminal) which comply
with JIS C2809-1992.
10A type: for plate thickness 0.5mm and
#187 tab terminal
20A type: for plate thickness 0.8mm and
#250 tab terminal
13. Avoid excessive load applied to
the terminal in case of installing such
as a bus bar etc., Because it might
adversely affect the opening and
closing performance.
14. Use the specied connector for the
connector terminal connection (80A,
120A and 300A)
Yazaki Corporation 7283 – 1020 or
equivalent
15. After the ON signal enters the 300A
type, automatic coil current switching
occurs after approximately 0.1
seconds. Do not repeatedly turn it OFF
within that 0.1 seconds interval, as
doing so may damage the relay.
All Rights Reserved C
OPYRIGHT Panasonic Electric Works Co., Ltd.
相關PDF資料 |
PDF描述 |
|---|---|
| AG603-89G | 0 MHz - 3000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AGA-3 | Cartridge Fuse; Current Rating:12.5mA; Voltage Rating:125V; Fuse Type:Fast Acting; Fuse Size/Group:1/4 x 1-1/4 "; Body Material:Glass; Diameter:6.35mm; Fuse Terminals:Ferrule; Leaded Process Compatible:No; Length:15.88mm RoHS Compliant: No |
| AGX-1 | Cartridge Fuse; Current Rating:1A; Voltage Rating:250V; Fuse Type:Fast Acting; Fuse Size/Group:1/4 x 1 "; Body Material:Glass; Diameter:6.35mm; Fuse Terminals:Ferrule; Leaded Process Compatible:No; Length:25.4mm RoHS Compliant: No |
| AGX-1/10 | Cartridge Fuse; Current Rating:100mA; Voltage Rating:250V; Fuse Type:Fast Acting; Fuse Size/Group:1/4 x 1 "; Body Material:Glass; Diameter:6.35mm; Fuse Terminals:Ferrule; Leaded Process Compatible:No; Length:25.4mm RoHS Compliant: No |
| AGX-1/100 | Cartridge Fuse; Current Rating:10mA; Voltage Rating:250V; Fuse Type:Fast Acting; Fuse Size/Group:1/4 x 1 "; Body Material:Glass; Diameter:6.35mm; Fuse Terminals:Ferrule; Leaded Process Compatible:No; Length:25.4mm RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AEV19024J | 制造商:Panasonic Electric Works 功能描述: |
| AEV19024W | 功能描述:車用繼電器 SPST-NO 300A 24VDC 12.9Ohm, Relay RoHS:否 制造商:Panasonic Electric Works 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:200 A 線圈電壓:12 VDC 線圈電阻: 線圈電流: 切換電壓: 安裝風格:Screw 觸點材料: |
| AEV25112 | 功能描述:RELAY AUTOMOTIVE DPST 150A 12V RoHS:是 類別:繼電器 >> 功率，高于 2 安 系列:AEV 其它有關文件:General Appl Guidelines Standards Chart 標準包裝:50 系列:JC 繼電器類型:通用 線圈類型:無鎖存 線圈電流:83.3mA 線圈電壓:12VDC 觸點形式:DPST（2 A 型） 觸點額定值（電流）:10A 切換電壓:250VAC - 最小值 關閉電壓（最大）:9.6 VDC 關閉電壓（最?。?1.2 VDC 特點:- 安裝類型:通孔 端接類型:PC 引腳 包裝:散裝 觸點材料:銀合金 操作時間:15ms 釋放時間:2ms 線圈功率:1 W 線圈電阻:144 歐姆 工作溫度:-50°C ~ 60°C |
| AEV31012 | 功能描述:車用繼電器 10A PCB type 12V RoHS:否 制造商:Panasonic Electric Works 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:200 A 線圈電壓:12 VDC 線圈電阻: 線圈電流: 切換電壓: 安裝風格:Screw 觸點材料: |
| AEV31024 | 功能描述:Automotive Relay SPST-NO (1 Form A) 24VDC Coil Through Hole 制造商:panasonic electric works 系列:AEV 包裝:散裝 零件狀態:有效 繼電器類型:汽車級 線圈類型:無鎖存 線圈電流:52mA 線圈電壓:24VDC 觸頭外形:SPST-NO（1 A 型） 額定接觸（電流）:10A 開關電壓:400VDC - 標稱 導通電壓（最大值）:18 VDC 關閉電壓（最小值）:2 VDC 工作時間:50ms 釋放時間:30ms 特性:- 安裝類型:通孔 端子類型:PC 引腳 觸頭材料:- 線圈功率:1.24 W 線圈電阻:- 工作溫度:-40°C ~ 80°C 標準包裝:25 |
發布緊急采購，3分鐘左右您將得到回復。