- 您現在的位置：買賣IC網 > PDF目錄375269 > ADXL210JE (ANALOG DEVICES INC) Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle PDF資料下載
參數資料
| 型號： | ADXL210JE |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Low-Cost 10 g Dual-Axis Accelerometer with Duty Cycle |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, CQCC8 |
| 封裝： | CERAMIC, LCC-8 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 169K |
| 代理商： | ADXL210JE |
REV. 0
ADXL210E
–8–
TEMPERATURE
–
C
1.06
0.94
–
45
90
–
30
P
–
15
0
15
30
45
60
75
1.04
1.02
1.00
0.98
0.96
TPC 25. Normalized DCM Period (T2) vs. Temperature
nominally 50% duty cycle. The acceleration signal can be deter-
mined by measuring the length of the T1 and T2 pulses with
a counter/timer or with a polling loop using a low cost micro-
controller.
An analog output voltage can be obtained either by buffering the
signal from the X
FILT
and Y
FILT
pin, or by passing the duty cycle
signal through an RC filter to reconstruct the dc value.
The ADXL210E will operate with supply voltages as low as 3.0 V
or as high as 5.25 V.
A(
g
) = (T1/T2
–
0.5)/4%
0
g
= 50% DUTY CYCLE
T2(s) = R
SET
( )/125M
T2
T1
Figure 1. Typical Output Duty Cycle
APPLICATIONS
POWER SUPPLY DECOUPLING
For most applications a single 0.1
μ
F capacitor, C
DC
, will
adequately decouple the accelerometer from signal and noise
on the power supply. However, in some cases, especially where
digital devices such as microcontrollers share the same power
supply, digital noise on the supply may cause interference on
the ADXL210E output. This may be observed as a slowly
undulating fluctuation of voltage at X
FILT
and Y
FILT
. If additional
decoupling is needed, a 100
(or smaller) resistor or ferrite
beads, may be inserted in the supply line of the ADXL210E.
C
DC
FERRITE BEAD
100
R
SET
Y
FILT
V
DD
COM
ST
T2
X
OUT
Y
OUT
X
FILT
Y
FILT
ADXL210E
X
FILT
V
DD
Figure 2.
DEFINITIONS
T1
T2
Duty Cycle
Length of the “on” portion of the cycle.
Length of the total cycle.
Ratio of the “on” time (T1) of the cycle to the total
cycle (T2). Defined as T1/T2 for the ADXL210E/
ADXL210.
Time period of the “on” pulse. Defined as T1 for
the ADXL210E/ADXL210.
Pulsewidth
THEORY OF OPERATION
The ADXL210E is a complete, dual-axis acceleration measure-
ment system on a single monolithic IC. It contains a polysilicon
surface-micromachined sensor and signal conditioning circuitry
to implement an open loop acceleration measurement architec-
ture. For each axis, an output circuit converts the analog signal to
a duty cycle modulated (DCM) digital signal that can be decoded
with a counter/timer port on a microprocessor. The ADXL210E
is capable of measuring both positive and negative accelerations
to
±
10
g
. The accelerometer can measure static acceleration
forces such as gravity, allowing it to be used as a tilt sensor.
The sensor is a surface micromachined polysilicon structure
built on top of the silicon wafer. Polysilicon springs suspend the
structure over the surface of the wafer and provide a resistance
against acceleration forces. Deflection of the structure is mea-
sured using a differential capacitor that consists of independent
fixed plates and central plates attached to the moving mass. The
fixed plates are driven by 180
°
out of phase square waves. An
acceleration will deflect the beam and unbalance the differential
capacitor, resulting in an output square wave whose amplitude
is proportional to acceleration. Phase sensitive demodulation
techniques are then used to rectify the signal and determine the
direction of the acceleration.
The output of the demodulator drives a duty cycle modulator
(DCM) stage through a 32 k
resistor. At this point a pin is
available on each channel to allow the user to set the signal band-
width of the device by adding a capacitor. This filtering improves
measurement resolution and helps prevent aliasing.
After being low-pass filtered, the analog signal is converted to a
duty cycle modulated signal by the DCM stage. A single resistor
sets the period for a complete cycle (T2), which can be set between
0.5 ms and 10 ms (see TPC 12). A 0
g
acceleration produces a
相關PDF資料 |
PDF描述 |
|---|---|
| ADXL213 | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL213AE-REEL | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL213AE | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL213EB | Low Cost 1.2 g Dual Axis Accelerometer |
| ADXL311 | Low Cost, Ultracompact 【2 g Dual-Axis Accelerometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADXL210JE-REEL | 制造商:Analog Devices 功能描述:Accelerometer Dual |
| ADXL210JQC | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost +-2 g/+-10 g Dual Axis iMEMS Accelerometers with Digital Output |
| ADXL210JQC-1 | 制造商:Analog Devices 功能描述: |
| ADXL212 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision ±2 g Dual Axis, PWM Output Accelerometer |
| ADXL212AEZ | 功能描述:IC ACCELEROMETER DUAL 8LCC RoHS:是 類別:傳感器，轉換器 >> 加速計 系列:- 標準包裝:1 系列:SCA1000 軸:X，Y 加速范圍:±1.7g 靈敏度:1.2V/g 電源電壓:4.75 V ~ 5.25 V 輸出類型:數字 帶寬:50±30Hz 接口:SPI 安裝類型:表面貼裝 封裝/外殼:12-SMD 供應商設備封裝:12-SMD 其它名稱:551-1007-1 |
發布緊急采購，3分鐘左右您將得到回復。