- 您現在的位置：買賣IC網 > PDF目錄8667 > ADV7120KSTZ30-REEL (Analog Devices Inc)IC DAC VIDEO 3CH 30MHZ 48-LQFP PDF資料下載
參數資料
| 型號： | ADV7120KSTZ30-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/12頁 |
| 文件大小： | 0K |
| 描述： | IC DAC VIDEO 3CH 30MHZ 48-LQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 2,000 |
| 設置時間： | 12ns |
| 位數： | 8 |
| 數據接口： | 并聯 |
| 轉換器數目： | 3 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 625mW |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 3 電流，單極 |
| 采樣率（每秒）： | 30M |
ADV7120
REV. B
–11–
Power Planes
The PC board layout should have two distinct power planes,
one for analog circuitry and one for digital circuitry. The analog
power plane should encompass the ADV7120 (VAA) and all as-
sociated analog circuitry. This power plane should be connected
to the regular PCB power plane (VCC) at a single point through
a ferrite bead, as illustrated in Figure 8. This bead should be lo-
cated within three inches of the ADV7120.
The PCB power plane should provide power to all digital logic
on the PC board, and the analog power plane should provide
power to all ADV7120 power pins, voltage reference circuitry
and any output amplifiers.
The PCB power and ground planes should not overlay portions
of the analog power plane. Keeping the PCB power and ground
planes from overlaying the analog power plane will contribute to
a reduction in plane-to-plane noise coupling.
Supply Decoupling
Noise on the analog power plane can be further reduced by the
use of multiple decoupling capacitors. (See Figure 8.)
Optimum performance is achieved by the use of 0.1
F ceramic
capacitors. Each of the two groups of VAA should be individually
decoupled to ground. This should be done by placing the ca-
pacitors as close as possible to the device with the capacitor
leads as short as possible, thus minimizing lead inductance.
It is important to note that while the ADV7120 contains cir-
cuitry to reject power supply noise, this rejection decreases with
frequency. If a high frequency switching power supply is used,
the designer should pay close attention to reducing power sup-
ply noise. A dc power supply filter (Murata BNX002) will pro-
vide EMI suppression between the switching power supply and
the main PCB. Alternatively, consideration could be given to
using a three terminal voltage regulator.
Digital Signal Interconnect
The digital signal lines to the ADV7120 should be isolated as
much as possible from the analog outputs and other analog cir-
cuitry. Digital signal lines should not overlay the analog power
plane.
Due to the high clock rates used, long clock lines to the
ADV7120 should be avoided so as to minimize noise pickup.
Any active pull-up termination resistors for the digital inputs
should be connected to the regular PCB power plane (VCC), and
not the analog power plane.
Analog Signal Interconnect
The ADV7120 should be located as close as possible to the out-
put connectors thus minimizing noise pickup and reflections
due to impedance mismatch.
The video output signals should overlay the ground plane, and
not the analog power plane, thereby maximizing the high fre-
quency power supply rejection.
For optimum performance, the analog outputs should each have
a source termination resistance to ground of 75
(doubly ter-
minated 75
configuration). This termination resistance should
be as close as possible to the ADV7120 so as to minimize
reflections.
Additional information on PCB design is available in an applica-
tion note entitled “Design and Layout of a Video Graphics Sys-
tem for Reduced EMI.” This application note is available from
Analog Devices, publication number E1309-15-10/89.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J5N-MX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| VE-230-MW-B1 | CONVERTER MOD DC/DC 5V 100W |
| VE-22W-MW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
| VE-J53-MX-B1 | CONVERTER MOD DC/DC 24V 75W |
| VE-JVX-MY | CONVERTER MOD DC/DC 5.2V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7120KSTZ50 | 功能描述:IC DAC VIDEO 3-CH 50MHZ 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| ADV7121 | 制造商:AD 制造商全稱:Analog Devices 功能描述:CMOS 80 MHz, Triple 10-Bit Video DACs |
| ADV7121JN30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC without Color Palette |
| ADV7121JN50 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC without Color Palette |
| ADV7121JN80 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC without Color Palette |
發布緊急采購，3分鐘左右您將得到回復。