參數資料
型號： ADUC816BCP
廠商： Analog Devices Inc
文件頁數： 50/68頁
文件大小： 0K
描述： IC MCU 8K FLASH ADC/DAC 56LFCSP
標準包裝： 1
系列： MicroConverter® ADuC8xx
核心處理器： 8052
芯體尺寸： 8-位
速度： 12.58MHz
連通性： I²C，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 34
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 640 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 7x16b; D/A 1x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 56-VFQFN 裸露焊盤，CSP
包裝： 托盤
產品目錄頁面： 738 (CN2011-ZH PDF)
REV. 0
ADuC816
–54–
TIMER/COUNTER 0 AND 1 OPERATING MODES
The following paragraphs describe the operating modes for timer/
counters 0 and 1. Unless otherwise noted, it should be assumed
that these modes of operation are the same for timer 0 as for timer 1.
Mode 0 (13-Bit Timer/Counter)
Mode 0 configures an 8-bit timer/counter with a divide-by-32
prescaler. Figure 33 shows mode 0 operation.
12
CORE
CLK*
TF0
INTERRUPT
CONTROL
P3.4/T0
GATE
P3.2/
INT0
TR0
TL0
(5 BITS)
TH0
(8 BITS)
C/
T = 0
C/
T = 1
*THE CORE CLOCK IS THE OUTPUT OF THE PLL AS DESCRIBED ON PAGE 42.
Figure 33. Timer/Counter 0, Mode 0
In this mode, the timer register is configured as a 13-bit register.
As the count rolls over from all 1s to all 0s, it sets the timer overflow
flag TF0. The overflow flag, TF0, can then be used to request an
interrupt. The counted input is enabled to the timer when TR0 = 1
and either Gate = 0 or
INT0 = 1. Setting Gate = 1 allows the timer
to be controlled by external input
INT0, to facilitate pulsewidth
measurements. TR0 is a control bit in the special function regis-
ter TCON; Gate is in TMOD. The 13-bit register consists of all
eight bits of TH0 and the lower five bits of TL0. The upper three
bits of TL0 are indeterminate and should be ignored. Setting the
run flag (TR0) does not clear the registers.
Mode 1 (16-Bit Timer/Counter)
Mode 1 is the same as Mode 0, except that the timer register is
running with all 16 bits. Mode 1 is shown in Figure 34.
12
CORE
CLK*
TF0
INTERRUPT
CONTROL
P3.4/T0
TL0
(8 BITS)
TH0
(8 BITS)
C/
T = 0
C/
T = 1
GATE
P3.2/
INT0
TR0
*THE CORE CLOCK IS THE OUTPUT OF THE PLL AS DESCRIBED ON PAGE 42.
Figure 34. Timer/Counter 0, Mode 1
Mode 2 (8-Bit Timer/Counter with Autoreload)
Mode 2 configures the timer register as an 8-bit counter (TL0)
with automatic reload, as shown in Figure 35. Overflow from TL0
not only sets TF0, but also reloads TL0 with the contents of TH0,
which is preset by software. The reload leaves TH0 unchanged.
12
CORE
CLK*
CONTROL
P3.4/T0
TF0
TL0
(8 BITS)
INTERRUPT
C/
T = 0
C/
T = 1
RELOAD
TH0
(8 BITS)
GATE
P3.2/
INT0
TR0
*THE CORE CLOCK IS THE OUTPUT OF THE PLL AS DESCRIBED ON PAGE 42.
Figure 35. Timer/Counter 0, Mode 2
Mode 3 (Two 8-Bit Timer/Counters)
Mode 3 has different effects on timer 0 and timer 1. Timer 1 in
Mode 3 simply holds its count. The effect is the same as setting
TR1 = 0. Timer 0 in Mode 3 establishes TL0 and TH0 as two
separate counters. This configuration is shown in Figure 36. TL0
uses the timer 0 control bits: C/T, Gate, TR0,
INT0, and TF0.
TH0 is locked into a timer function (counting machine cycles)
and takes over the use of TR1 and TF1 from timer 1. Thus, TH0
now controls the “timer 1” interrupt. Mode 3 is provided for
applications requiring an extra 8-bit timer or counter.
When timer 0 is in Mode 3, timer 1 can be turned on and off by
switching it out of, and into, its own Mode 3, or can still be used by
the serial interface as a Baud Rate Generator. In fact, it can be used,
in any application not requiring an interrupt from timer 1 itself.
12
CORE
CLK*
TL0
(8 BITS)
TF0
INTERRUPT
CONTROL
P3.4/T0
C/
T = 0
C/
T = 1
TH0
(8 BITS)
TF1
INTERRUPT
CORE
CLK/12
TR1
CORE
CLK/12
CONTROL
GATE
P3.2/
INT0
TR0
*THE CORE CLOCK IS THE OUTPUT OF THE PLL AS DESCRIBED ON PAGE 42.
Figure 36. Timer/Counter 0, Mode 3
REV. A
相關PDF資料
PDF描述
ADUC824BSZ-REEL IC MCU 8K FLASH ADC/DAC 52MQFP
ADUC831BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC832BSZ-REEL IC MCU 62K FLASH ADC/DAC 52MQFP
ADUC834BCPZ-REEL IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC836BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
相關代理商/技術參數
參數描述
ADUC816BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:MCU 8BIT CISC 8KB FLASH 3.3V/5V 56LFCSP EP - Tape and Reel
ADUC816BCPZ 功能描述:IC MCU FLASH 16BIT ADC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC816BCPZ-REEL 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 12.58MHz 8KB (8K x 8) FLASH 56-LFCSP (8x8) 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包裝:帶卷（TR） 零件狀態:上次購買時間 核心處理器:8052 核心尺寸:8-位 速度:12.58MHz 連接性:I2C，SPI，UART/USART 外設:PSM，溫度傳感器，WDT I/O 數:34 程序存儲容量:8KB（8K x 8） 程序存儲器類型:閃存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 電壓 - 電源（Vcc/Vdd）:2.7 V ~ 5.5 V 數據轉換器:A/D 7x16b；D/A 1x12b 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:56-WFQFN 裸焊盤，CSP 供應商器件封裝:56-LFCSP (8x8) 標準包裝:1
ADUC816BS 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +16BIT ADC MQFP52 816
ADUC816BS-REEL 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*