- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC7034BCPZ (Analog Devices Inc)IC MCU FLASH 32K ANLG IO 48LFCSP PDF資料下載
參數資料
| 型號： | ADUC7034BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 26/136頁 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 32K ANLG IO 48LFCSP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI，UART/USART |
| 外圍設備： | POR，PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 9 |
| 程序存儲器容量： | 32KB（16K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 115°C |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
ADuC7034
Rev. B | Page 121 of 136
LIN Hardware Synchronization Timer0 Register
Name:
LHSVAL0
Address:
0xFFFF0788
Default Value:
0x0000
Access:
Read only
Function:
The 16-bit, read only LHSVAL0 register holds
the value of the internal LIN synchronization
timer. The LIN synchronization timer is
clocked from an internal 5 MHz clock and is
independent of core clock and baud rate
frequency. In LIN mode, the value read by user
code from the LHSVAL0 register can be used
to calculate the master LIN baud rate. This
calculation is then used to configure the
internal UART baud rate to ensure correct LIN
communication via the UART from the
ADuC7034 slave to the LIN master node.
LIN Hardware Break Timer1 Register
Name:
LHSVAL1
Address:
0xFFFF0790
Default Value:
0x000 (read) or 0x047 (write)
Access:
Read/write
Function:
When user code reads this location, the 12-bit
value returned is the value of the internal LIN
break timer, which is clocked directly from the
on-chip low power 131 kHz oscillator and
times the LIN break pulse. A negative edge on
the LIN bus or user code reading the
LHSVAL1 results in the timer and the register
contents being reset to 0.
When user code writes to this location, the 12-bit value is
written not to the LIN break timer, but to a LIN break compare
register. In LIN mode of operation, the value in the compare
register is continuously compared to the break timer value. A
LIN break interrupt (IRQEN[7] and LHSSTA[0]) is generated
when the timer value reaches the compare value. After the
break condition interrupt, the LIN break timer continues to
count until the rising edge of the break signal. If a rising edge is
not detected and the 12-bit timer overflows (4096 × 1/131 kHz
= 31 ms), a break field error interrupt (IRQEN[7] and
LHSSTA[4]) is generated. By default, the value in the compare
register is 0x47, corresponding to 11 bit periods (that is, the
minimum pulse width for a LIN break pulse at 20 kbps). For
different baud rates, this value can be changed by writing to
LHSVAL1. Note that if a valid break interrupt is not received,
subsequent sync pulse timing through the LHSVAL0 register
does not occur.
LIN HARDWARE INTERFACE
LIN Frame Protocol
The LIN frame protocol is broken into four main categories:
break symbol, sync byte, protected identifier, and data bytes.
The format of the frame header, break symbol, sync byte, and
protected identifier are shown in Figure 46. Essentially, the
embedded UART, the LIN hardware synchronization logic, and
the high voltage transceiver interface all combine on chip to
support and manage LIN-based transmissions and receptions.
LIN Frame Break Symbol
As shown in Figure 47, the LIN break symbol, which lasts at
least 13 bit periods, is used to signal the start of a new frame. The
slave must be able to detect a break symbol even while expecting or
receiving data. The ADuC7034 accomplishes this by using the
LHSVAL1 break condition and break error detect functionality
as described in the LIN Hardware Break Timer1 Register
section. The break period does not have to be accurately
measured, but if a bus fault condition (bus held low) occurs, it
must be flagged.
LIN Frame Synchronization Byte
The baud rate of the communication using LIN is calculated
from the sync byte, as shown in Figure 48. The time between
the first falling edge of the sync field and the fifth falling edge of
the sync field is measured and then divided by 8 to determine the
baud rate of the data that is to be transmitted. The ADuC7034
implements the timing of this sync byte in hardware. For
more information on this feature, refer to the LIN Hardware
Synchronization Status Register section.
LIN Frame Protected Identifier
After receiving the LIN sync field, the required baud rate for
UART is calculated. UART is then configured, allowing the
ADuC7034 to receive the protected identifier, as shown in
Figure 49. The protected identifier consists of two subfields: the
identifier and the identifier parity. The 6-bit identifier contains
the identifier of the target for the frame. The identifier signifies
the number of data bytes to be either received or transmitted. The
number of bytes is user configurable at the system-level design.
The parity is calculated on the identifier and is dependent on
the revision of LIN for which the system is designed.
LIN Frame Data Byte
The data byte frame carries between one and eight bytes of
data. The number of bytes contained in the frame is dependent
on the LIN master. The data byte frame is split into data bytes
as shown in Figure 50.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7036CCPZ | IC MCU 96K FLASH DUAL 48LFCSP |
| ADUC7039BCP6Z-RL | IC MCU ARM7 BATT SENSER 32LFCSP |
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7122BBCZ-RL | PRECISION ANALOG MCU I.C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7034BCPZ-RL | 功能描述:IC MCU FLASH 32K ANLG IO 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7036 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor for Automotive |
| ADUC7036BCPZ | 功能描述:IC MCU FLASH 96K ANLGI/O 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7036BCPZ-RL | 功能描述:IC SENSOR AUTO 96K FLASH 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7036CCPZ | 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。