- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7486AARMZ-RL (ON Semiconductor)IC TEMP SENS DGTL 2CH SST 10MSOP Datasheet資料下載
參數資料
| 型號： | ADT7486AARMZ-RL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 9/14頁 |
| 文件大小： | 369K |
| 描述： | IC TEMP SENS DGTL 2CH SST 10MSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±1.75°C（最小值） |
| 拓?fù)洌?/td> | ADC，多路復用器，寄存器庫 |
| 輸出類型： | Simple Serial Transport?（SST） |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
ADT7484A/ADT7486A
http://onsemi.com
9
Temperature Measurement
The ADT7484A/ADT7486A each have two dedicated
temperature measurement channels: one for measuring the
temperature of an on-chip band gap temperature sensor, and
one for measuring the temperature of a remote diode, usually
located in the CPU or GPU.
The ADT7484A monitors one local and one remote
temperature channel, whereas the ADT7486A monitors one
local and two remote temperature channels. Monitoring of
each of the channels is done in a round-robin sequence. The
monitoring sequence is in the order shown in Table 11.
Table 11. TEMPERATURE MONITORING SEQUENCE
Channel
Number
Measurement
Conversion
Time (ms)
0
Local Temperature
12
1
Remote Temperature 1
38
2
Remote Temperature 2
(ADT7486A Only)
38
Temperature Measurement Method
A simple method for measuring temperature is to exploit
the negative temperature coefficient of a diode by measuring
the base-emitter voltage (V
BE
) of a transistor operated at
constant current. Unfortunately, this technique requires
calibration to null the effect of the absolute value of V
BE
,
which varies from device to device.
The technique used in the ADT7484A/ADT7486A
measures the change in V
BE
when the device is operated at
three different currents.
Figure 14 shows the input signal conditioning used to
measure the output of a remote temperature sensor. This
figure shows the remote sensor as a substrate transistor,
which is provided for temperature monitoring on some
microprocessors, but it could also be a discrete transistor. If
a discrete transistor is used, the collector is not grounded and
should be linked to the base. To prevent ground noise from
interfering with the measurement, the more negative
terminal of the sensor is not referenced to ground, but is
biased above ground by an internal diode at the D1 input.
If the sensor is operating in an extremely noisy environment,
C1 can be added as a noise filter. Its value should not exceed
1,000 pF.
To measure DV
BE
, the operating current through the
sensor is switched between three related currents. Figure 14
shows N1 ?I and N2 ?I as different multiples of the current
I. The currents through the temperature diode are switched
between I and N1 ?I, giving DV
BE1
, and then between I and
N2 ?I, giving DV
BE2
. The temperature can then be
calculated using the two DV
BE
measurements. This method
can also cancel the effect of series resistance on the
temperature measurement. The resulting DV
BE
waveforms
are passed through a 65 kHz low-pass filter to remove noise
and then through a chopper-stabilized amplifier to amplify
and rectify the waveform, producing a dc voltage
proportional to DV
BE
. The ADC digitizes this voltage, and
a temperature measurement is produced. To reduce the
effects of noise, digital filtering is performed by averaging
the results of 16 measurement cycles for low conversion
rates. Signal conditioning and measurement of the internal
temperature sensor is performed in the same manner.
Figure 14. Signal Conditioning for Remote Diode Temperature Sensors
LOW-PASS FILTER
f
C
= 65 kHz
REMOTE
SENSING
TRANSISTOR
BIAS
DIODE
D+
D
V
CC
I
BIAS
I
N2 ?I
V
OUT+
V
OUT
To ADC
C1*
*CAPACITOR C1 IS OPTIONAL. IT SHOULD ONLY BE USED IN NOISY ENVIRONMENTS.
N1 ?I
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7488AARMZ-RL | IC TEMP/VOLT DGTL W/SST 10MSOP |
| ADT7518ARQZ | IC SENSOR TEMP QD ADC/DAC 16QSOP |
| AT30TS00-MAH-T | SENSOR DGTL TEMP I2C/SMBUS 8WDFN |
| AT30TSE002B-MAH-T | SENSOR DGTL TEMP I2C/SMBUS 8WDFN |
| BD3504FVM-TR | IC REG CTRLR SGL POS ADJ 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7488A | 制造商:AD 制造商全稱:Analog Devices 功能描述:SST Digital Temperature Sensor and Voltage Monitor |
| ADT7488AARMZ-REEL | 功能描述:IC TEMP SENSOR SST DGTL 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7488AARMZ-REEL7 | 功能描述:IC TEMP/VOLT DGTL W/SST 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7488AARMZ-RL | 功能描述:板上安裝溫度傳感器 TMP SNSR/VLTG MON W/SST INTERFACE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7488AARMZ-RL7 | 功能描述:板上安裝溫度傳感器 TMP SNSR/VLTG MON W/SST INTERFACE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。