- 您現在的位置：買賣IC網 > PDF目錄67358 > ADT7485ARMZ (ON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADT7485ARMZ |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| 封裝： | LEAD FREE, PLASTIC, MO-187-BA, MSOP-10 |
| 文件頁數： | 3/16頁 |
| 文件大小： | 235K |
| 代理商： | ADT7485ARMZ |
Preliminary Technical Data
ADT7485
Rev. PrA | Page 11 of 16
Command Code Details
ADT7485 Device Identifier Block
The GetDIB() command retrieves the device identifier block
(DIB), which provides information to identify the capabilities of
the ADT7485. The data returned can be in 8- or 16-byte format.
The full 16 bytes of DIB is detailed in Table 7. The 8-byte format
involves the first eight bytes described in this table. Byte-sized
data is returned in the respective fields as it appears in Table 7.
Word-sized data, including vendor ID, device ID, and data
values use little endian format, that is, the LSB is returned first,
followed by the MSB.
Table 7. 16-Byte DIB Details
Name
Value
Description
Device Capabilities
0xc0
Fixed address device.
Version/Revision
0x40
Meets Version 1 of the SST
specification
Vendor ID
00x11d4
Contains company ID
number in little endian
format
Device ID
0x7485
Contains device ID number
in little endian format
Device Interface
0x01
SST device
Function Interface
0x00
Reserved
0x00
Reserved
0x00
Reserved
Vendor Specific ID
0x00
Reserved
Client Device Address
0x48 to
0x4a
Dependent on the state of
the address pin.
Ping()
The Ping() command verifies if a device is responding at a
particular address. The ADT7485 shows a valid nonzero FCS in
response to the Ping() command when correctly addressed.
Table 8. Ping() Command
Target Address
Write Length
Read Length
FCS
(Not necessary)
0x00
ResetDevice()
This command resets the register map and conversion
controller. The reset command can be global or directed at the
client address of the ADT7485.
Table 9. ResetDevice() Command
Target Address
Write
Length
Read
Length
Reset
command
FCS
Device Address
0x01
0x00
0xf6
GetIntTemp()
The ADT7485 shows the local temperature of the device in
response to the GetIntTemp() command. The data has a little
endian, 16-bit, twos compliment format.
GetExtTemp()
Prompted by the GetExtTemp() command, the ADT7485 shows
the temperature of the remote diode in little endian, 16-bit,
twos compliment format. The ADT7485 shows 0x8000 in
response to this command if the external diode is an open or
short circuit.
GetAllTemps()
The ADT7485 shows the local and remote temperatures in a
4-byte block of data (internal temperature first, followed by
external temperature) in response to a GetAllTemps()
command.
SetExtOffset()
This command sets the offset that the ADT7485 will use to
correct errors in the external diode. The offset is set in little
endian, 16-bit, twos compliment format. The maximum offset is
±128°C with +0.25°C resolution.
GetExtOffset()
This command causes the ADT7485 to show the offset that it is
using to correct errors in the external diode. The offset value is
returned in little endian format, that is, LSB before MSB.
ADT7485 Response to Unsupported Commands
A full list of command codes supported by the ADT7485 is
given in Table 6. The offset registers (Command Code 0xe0) are
the only registers that the user can write to. The other defined
registers are read only. Writing to Register Addresses 0x02,
0x09, and 0x15 to 0xdf shows a valid FSC, but no action is taken
by the ADT7485. The ADT7485 shows an invalid FSC if the
user attempts to write to the device between Command Codes
0xe2 to 0xee. These registers are reserved for the manufacturer’s
use only, and no data can be written to the device via these
addresses.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7485ARMZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7486ARMZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7486ARMZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7484ARMZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7484ARMZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7486A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Digital Temperature Sensor with SST Interface |
| ADT7486AARMZ-R7 | 功能描述:板上安裝溫度傳感器 DGL TMP SNSR SST INF RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7486AARMZ-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Digital Temperature Sensor with SST Interface |
| ADT7486AARMZ-REEL7 | 功能描述:IC TEMP SENS DGTL 2CH SST 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7486AARMZ-RL | 功能描述:板上安裝溫度傳感器 DGL TMP SNSR SST INF RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。