參數資料
型號： ADT7411ARQZ-REEL7
廠商： ANALOG DEVICES INC
元件分類： 溫度/濕度傳感器
英文描述： Circular Connector; No. of Contacts:55; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:17-35
中文描述： DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 5Cel, RECTANGULAR, SURFACE MOUNT
封裝： MO-137-AB, LEAD FREE, QSOP-16
文件頁數： 29/36頁
文件大?。?/td> 456K
代理商： ADT7411ARQZ-REEL7
ADT7411
Rev. A | Page 29 of 36
The I
2
C address set up by the ADD pin is not latched by
the device until after this address has been sent twice. On
the eighth SCL cycle of the second valid communication,
the serial bus address is latched in. This is the SCL cycle
directly after the device has seen its own I
2
C serial bus
address. Any subsequent changes on this pin will have no
effect on the I
2
C serial bus address.
Writing to the ADT7411
Depending on the register being written to, there are two dif-
ferent writes for the ADT7411. It is not possible to do a block
write to this part, i.e., no I
2
C auto-increment.
Writing to the Address Pointer Register for a Subsequent
Read
In order to read data from a particular register, the address
pointer register must contain the address of that register. If it
does not, the correct address must be written to the address
pointer register by performing a single-byte write operation, as
shown in Figure 34. The write operation consists of the serial
bus address followed by the address pointer byte. No data is
written to any of the data registers. A read operation is then
performed to read the register.
Writing Data to a Register
All registers are 8-bit registers so only one byte of data can be
written to each register. Writing a single byte of data to one of
these read/write registers consists of the serial bus address, the
data register address written to the address pointer register,
followed by the data byte written to the selected data register.
This is illustrated in Figure 35. To write to a different register,
another START or repeated START is required. If more than
one byte of data is sent in one communication operation, the
addressed register will be repeatedly loaded until the last data
byte has been sent.
Reading Data From the ADT7411
Reading data from the ADT7411 is done in a one-byte
operation. Reading back the contents of a register is shown in
Figure 36. The register address had previously been set up by a
single-byte write operation to the Address Pointer register. To
read from another register, write to the Address Pointer register
again to set up the relevant register address. Thus, block reads
are not possible, i.e., no I
2
C auto-increment.
SPI Serial Interface
The SPI serial interface of the ADT7411 consists of four wires:
CS, SCLK, DIN, and DOUT. The CS is used to select the device
when more than one device is connected to the serial clock and
data lines. The CS is also used to distinguish between any two
separate serial communications (see Figure 41 for a graphical
explanation). The SCLK is used to clock data in and out of the
part. The DIN line is used to write to the registers, and the
DOUT line is used to read data back from the registers. The
recommended pull-up resistor value is between 500 and
820 .
0
A
B
CS
(START HIGH)
SPI LOCKED ON
THIRD RISING EDGE
C
SPI FRAMING
EDGE
A
B
CS
(START LOW)
SPI LOCKED ON
THIRD RISING EDGE
C
SPI FRAMING
EDGE
Figure 33. Serial Interface—Selecting and Locking SPI Protocol
0
0
1
1
0
0
R/W
SCL
SDA
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
ACK. BY
ADT7411
ACK. BY
ADT7411
STOP BY
MASTER
START BY
MASTER
A2
A1
A
P7
P6
P5
P4
P3
P2
P1
P0
9
1
9
1
Figure 34. I
2
C—Writing to the Address Pointer Register to Select a Register for a Subsequent Read Operation
相關PDF資料
PDF描述
ADT7411ARQZ10 LJT 6C 6#12 SKT RECP
ADuC812(中文) 12-Bit ADC with Embedded FLASH MCU(12位8通道A/D轉換器)
ADUC812BS-REEL MSC-51 8K-Flash/256-RAM/640-EEPROM(543.84 k)
ADuC812 12-Bit ADC with Embedded FLASH MCU(12位8通道A/D轉換器)
ADUC812 Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No
相關代理商/技術參數
參數描述
ADT7411ARQZ-REEL71 制造商:AD 制造商全稱:Analog Devices 功能描述:SPI??-/I2C??-Compatible, 10-Bit Digital Temperature Sensor and 8-Channel ADC
ADT7420 制造商:AD 制造商全稱:Analog Devices 功能描述:±0.25°C Accurate, 16-Bit Digital I2C Temperature Sensor
ADT7420_12 制造商:AD 制造商全稱:Analog Devices 功能描述:?±0.25?°C Accurate, 16-Bit Digital I2C Temperature Sensor
ADT7420UCPZ 制造商:AD 制造商全稱:Analog Devices 功能描述:±0.25°C Accurate, 16-Bit Digital I2C Temperature Sensor
ADT7420UCPZ-R2 功能描述:板上安裝溫度傳感器 +/-0.25C accurate 12C Temperature Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*