- 您現在的位置：買賣IC網 > PDF目錄67358 > ADT7408CCPZ2-REEL (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 4Cel, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADT7408CCPZ2-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 4Cel, SQUARE, SURFACE MOUNT |
| 封裝： | 3 X 3 MM, MO-229VEED-4, LFCSP-8 |
| 文件頁數： | 19/22頁 |
| 文件大?。?/td> | 570K |
| 代理商： | ADT7408CCPZ2-REEL |
ADT7408
Preliminary Technical Data
Rev. PrC | Page 6 of 22
THEORY OF OPERATION
CIRCUIT INFORMATION
The ADT7408 is a 12-bit digital temperature sensor. Its output
is Two’s complement that the 12th bit is the sign bit. An on-
board sensor generates a voltage precisely proportional to
absolute temperature, which is compared to an internal voltage
reference and is input to a precision digital modulator. Overall
accuracy for the ADT7408 is ±2°C from 75°C to 95°C, ±3°C
from 40°C to +125°C, and ±4°C from -20°C to +125°C with
excellent transducer linearity. The serial interface is SMBus-
/I2C- compatible and the open-drain output of the ADT7408 is
capable of sinking 6 mA.
The on-board temperature sensor has excellent accuracy and
linearity over the entire rated temperature range without
needing correction or calibration by the user.
The sensor output is digitized by a first-order ∑- modulator,
also known as the charge balance type analog-to-digital
converter. This type of converter utilizes time-domain over-
sampling and a high accuracy comparator to deliver 12 bits of
effective accuracy in an extremely compact circuit.
CONVERTER DETAILS
The ∑- modulator consists of an input sampler, a summing
network, an integrator, a comparator, and a 1-bit DAC. This
architecture creates a negative feedback loop that minimizes the
integrator output by changing the duty cycle of the comparator
output in response to input voltage changes. The comparator
samples the output of the integrator at a much higher rate than
the input sampling frequency, called oversampling.
Oversampling spreads the quantization noise over a much
wider band than that of the input signal, improving overall
noise performance and increasing accuracy.
Figure 4. First-Order
∑- Modulator
The modulated output of the comparator is encoded using a
circuit technique that results in SMBus/I2C temperature data.
FUNCTIONAL DESCRIPTION
The conversion clock for the part is internally generated. No
external clock is required except when reading from and
writing to the serial port. In normal mode, the internal clock
oscillator runs an automatic conversion sequence. During this
automatic conversion sequence, a conversion is initiated every
100 ms. At this time, the part powers up its analog circuitry and
performs a temperature conversion. This temperature
conversion typically takes 60 ms, after which time the analog
circuitry of the part automatically shuts down. The analog
circuitry powers up again 40 ms later, when the 100 ms timer
times out and the next conversion begins. The result of the most
recent temperature conversion is always available in the
temperature value register as the SMBus/I2C circuitry never
shuts down.
The ADT7408 can be placed in a shutdown mode via the
configuration register, in which case the on-chip oscillator is
shut down and no further conversions are initiated until the
ADT7408 is taken out of shutdown mode. The ADT7408 can be
taken out of shutdown mode by writing zero to Bit D8 in the
configuration register. The conversion result from the last
conversion prior to shut-down can still be read from the
ADT7408 even when it is in shutdown mode.
In normal conversion mode, the internal clock oscillator is reset
after every read or write operation. This causes the device to
start a temperature conversion, the result of which is typically
available 60 ms later. Similarly, when the part is taken out of
shutdown mode, the internal clock oscillator is started and a
conversion is initiated. The conversion result is typically
available 60 ms later. Reading from the device before a
conversion is complete causes the ADT7408 to stop converting;
the part starts again when serial communication is finished.
This read operation provides the previous result.
The measured temperature value is compared with the
temperature set at the Alarm Temp Upper Boundary Trip
Register, the Alarm Temp Lower Boundary Trip Register, and
the Critical Temp Trip Register. If the measured value exceeds
these limits then the EVENT# pin is activated. This EVENT#
output is programmable for interrupt mode, comparator mode,
and also the output polarity via the configuration register.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7408CCPZ2-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 4Cel, SQUARE, SURFACE MOUNT |
| ADT7461AARMZ-2RL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7461AARMZ-002 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7470ARQZ | DIGITAL TEMP SENSOR-SERIAL, 7BIT(s), RECTANGULAR, SURFACE MOUNT |
| ADT7473ARQZ-1REEL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7408CCPZ-R2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:+-2 C Accurate, 12-Bit Digital Temperature Sensor |
| ADT7408CCPZ-REEL | 功能描述:IC TEMP SENSOR 12BIT ADC 8LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| ADT7408CCPZ-REEL7 | 功能描述:IC TEMP SENSOR 12BIT ADC 8LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| ADT7410 | 制造商:AD 制造商全稱:Analog Devices 功能描述:±0.5°C Accurate, 16-Bit Digital I2C Temperature Sensor |
| ADT7410TRZ | 功能描述:IC SENSOR TEMP 16BIT I2C 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:3,000 系列:- 功能:溫度開關 傳感器類型:內部 感應溫度:85°C 分界點 精確度:±6°C（最小值） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:開路漏極 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:ADT6501SRJZP085RL7-ND |
發布緊急采購，3分鐘左右您將得到回復。