- 您現在的位置：買賣IC網 > PDF目錄19372 > ADSP-TS101SAB1-000 (Analog Devices Inc)IC DSP CONTROLLER 6MBIT 625 BGA PDF資料下載
參數資料
| 型號： | ADSP-TS101SAB1-000 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 48/48頁 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 6MBIT 625 BGA |
| 標準包裝： | 1 |
| 系列： | TigerSHARC® |
| 類型： | 定點/浮點 |
| 接口： | 主機接口，連接端口，多處理器 |
| 時鐘速率： | 250MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 768kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.20V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 625-BBGA |
| 供應商設備封裝： | 625-PBGA（27x27） |
| 包裝： | 托盤 |
| 其它名稱： | ADSP-TS101SAB1000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁
ADSP-TS101S
Rev. C
|
Page 9 of 48
|
May 2009
LINK PORTS
The DSP’s four link ports provide additional 8-bit bidirectional
I/O capability. With the ability to operate at a double data rate—
latching data on both the rising and falling edges of the clock—
running at 125 MHz, each link port can support up to
250M bytes per second, for a combined maximum throughput
of 1G bytes per second.
The link ports provide an optional communications channel
that is useful in multiprocessor systems for implementing point-
to-point interprocessor communications. Applications can also
use the link ports for booting.
Each link port has its own double-buffered input and output
registers. The DSP’s core can write directly to a link port’s trans-
mit register and read from a receive register, or the DMA
controller can perform DMA transfers through eight (four
transmit and four receive) dedicated link port DMA channels.
Each link port has three signals that control its operation.
LxCLKOUT and LxCLKIN implement clock/acknowledge
handshaking. LxDIR indicates the direction of transfer and is
used only when buffering the LxDAT signals. An example appli-
cation would be using differential low-swing buffers for long
twisted-pair wires. LxDAT provides the 8-bit data bus
input/output.
Applications can program separate error detection mechanisms
for transmit and receive operations (applications can use the
checksum mechanism to implement consecutive link port
transfers), the size of data packets, and the speed at which bytes
are transmitted.
Under certain conditions, the link port receiver can initiate a
token switch to reverse the direction of transfer; the transmitter
becomes the receiver and vice versa.
TIMER AND GENERAL-PURPOSE I/O
The ADSP-TS101S has a timer pin (TMR0E) that generates out-
put when a programmed timer counter has expired. Also, the
DSP has four programmable general-purpose I/O pins
(FLAG3–0) that can function as either single-bit input or out-
put. As outputs, these pins can signal peripheral devices; as
inputs, they can provide the test for conditional branching.
RESET AND BOOTING
The ADSP-TS101S has two levels of reset (see reset specifica-
tions Page 24):
Power-up reset—after power-up of the system, and strap
options are stable, the RESET pin must be asserted (low).
Normal reset—for any resets following the power-up reset
sequence, the RESET pin must be asserted.
The DSP can be reset internally (core reset) by setting the
SWRST bit in SQCTL. The core is reset, but not the external
port or I/O.
After reset, the ADSP-TS101S has four boot options for begin-
ning operation:
Boot from EPROM. The DSP defaults to EPROM booting
when the BMS pin strap option is set low. See Strap Pin
Boot by an external master (host or another ADSP-
TS101S). Any master on the cluster bus can boot the
ADSP-TS101S through writes to its internal memory or
through autoDMA.
Boot by link port. All four receive link DMA channels are
initialized after reset to transfer a 256-word block to inter-
nal memory address 0 to 255, and to issue an interrupt at
the end of the block (similar to EP DMA). The correspond-
ing DMA interrupts are set to address zero (0).
No boot—Start running from an external memory. Using
the “no boot” option, the ADSP-TS101S must start running
from an external memory, caused by asserting one of the
IRQ3–0 interrupt signals.
The ADSP-TS101S core always exits from reset in the idle state
and waits for an interrupt. Some of the interrupts in the inter-
rupt vector table are initialized and enabled after reset.
LOW POWER OPERATION
The ADSP-TS101S can enter a low power sleep mode in which
its core does not execute instructions, reducing power con-
sumption to a minimum. The ADSP-TS101S exits sleep mode
when it senses a falling edge on any of its IRQ3–0 interrupt
inputs. The interrupt, if enabled, causes the ADSP-TS101S to
execute the corresponding interrupt service routine. This fea-
ture is useful for systems that require a low power standby
mode.
CLOCK DOMAINS
As shown in Figure 5, the ADSP-TS101S has two clock inputs,
SCLK (system clock) and LCLK (local clock).
These inputs drive its two major clock domains:
SCLK (system clock). Provides clock input for the external
bus interface and defines the ac specification reference for
the external bus signals. The external bus interface runs at
1 the SCLK frequency. A DLL locks internal SCLK to
SCLK input.
LCLK (local clock). Provides clock input to the internal
clock driver, CCLK, which is the internal clock for the core,
internal buses, memory, and link ports. The instruction
execution rate is equal to CCLK. A PLL from LCLK gener-
Figure 5. Clock Domains
LCLKRATx
SCLK_P
LCLK_P
SPD BITS,
LCTLx REGISTER
EXTERNAL INTERFACE
CCLK
(INSTRUCTION RATE)
LxCLKOUT/LxCLKIN
(LINK PORT RATE)
DLL
PLL
DLL
/LR
相關PDF資料 |
PDF描述 |
|---|---|
| RSM43DREH | CONN EDGECARD 86POS .156 EYELET |
| 1N4148TA | DIODE SS FAST 100V 200MA DO35 |
| ADSP-21160NKB-100 | IC DSP CONTROLLER 32BIT 400BGA |
| RMM43DREH | CONN EDGECARD 86POS .156 EYELET |
| RS-0509D/H3 | CONV DC/DC 2W 4.5-9VIN +/-09V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-TS101SAB1-100 | 功能描述:IC DSP CTRLR 128BIT BUS 625BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS101SAB1Z000 | 功能描述:IC DSP CONTROLLER 6MBIT 625-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS101SAB1Z100 | 功能描述:IC DSP CTRLR 128BIT BUS 625-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-TS101SAB2-000 | 功能描述:IC DSP CONTROLLER 6MBIT 484 BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS101SAB2-050 | 制造商:Analog Devices 功能描述:TIGERSHARC - Trays |
發布緊急采購，3分鐘左右您將得到回復。