參數資料
型號： ADSP-21489BSWZ-4B
廠商： Analog Devices Inc
文件頁數： 6/68頁
文件大小： 0K
描述： IC CCD SIGNAL PROCESSOR 176LQFP
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： EBI/EMI，DAI，I²C，SPI，SPORT，UART/USART
時鐘速率： 400MHz
非易失內存： 外部
芯片上RAM： 5Mb
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.10V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 176-LQFP 裸露焊盤
供應商設備封裝： 176-LQFP-EP（24x24）
包裝： 托盤
Rev. B
|
Page 14 of 68
|
March 2013
PIN FUNCTION DESCRIPTIONS
Table 11. Pin Descriptions
Name
Type
State
During/
After Reset
Description
ADDR23–0
I/O/T (ipu)
High-Z/
driven low
(boot)
External Address. The processor outputs addresses for external memory and periph-
erals on these pins. The ADDR pins can be multiplexed to support the external memory
interface address, and FLAGS15–8 (I/O) and PWM (O). After reset, all ADDR pins are in
external memory interface mode and FLAG(0–3) pins are in FLAGS mode (default).
When configured in the IDP_PDAP_CTL register, IDP channel 0 scans the ADDR23–4 pins
for parallel input data.
DATA15–0
I/O/T (ipu)
High-Z
External Data. The data pins can be multiplexed to support the external memory
interface data (I/O), and FLAGS7–0 (I/O).
AMI_ACK
I (ipu)
Memory Acknowledge. External devices can deassert AMI_ACK (low) to add wait
states to an external memory access. AMI_ACK is used by I/O devices, memory
controllers, or other peripherals to hold off completion of an external memory access.
MS0–1
O/T (ipu)
High-Z
Memory Select Lines 0–1. These lines are asserted (low) as chip selects for the corre-
sponding banks of external memory. The MS1-0 lines are decoded memory address lines
that change at the same time as the other address lines. When no external memory
access is occurring the MS1-0 lines are inactive; they are active however when a condi-
tional memory access instruction is executed, when the condition evaluates as true.
The MS1 pin can be used in EPORT/FLASH boot mode. For more information, see the
ADSP-214xx SHARC Processor Hardware Reference.
AMI_RD
O/T (ipu)
High-Z
AMI Port Read Enable. AMI_RD is asserted whenever the processor reads a word from
external memory.
AMI_WR
O/T (ipu)
High-Z
AMI Port Write Enable. AMI_WR is asserted when the processor writes a word to
external memory.
FLAG0/IRQ0
I/O (ipu)
FLAG[0]
INPUT
FLAG0/Interrupt Request0.
FLAG1/IRQ1
I/O (ipu)
FLAG[1]
INPUT
FLAG1/Interrupt Request1.
FLAG2/IRQ2/MS2
I/O (ipu)
FLAG[2]
INPUT
FLAG2/Interrupt Request2/Memory Select2.
FLAG3/TMREXP/MS3
I/O (ipu)
FLAG[3]
INPUT
FLAG3/Timer Expired/Memory Select3.
The following symbols appear in the Type column of this table: A = asynchronous, I = input, O = output, S = synchronous, A/D = active drive,
O/D = open drain, and T = three-state, ipd = internal pull-down resistor, ipu = internal pull-up resistor.
The internal pull-up (ipu) and internal pull-down (ipd) resistors are designed to hold the internal path from the pins at the expected logic
levels. To pull-up or pull-down the external pads to the expected logic levels, use external resistors. Internal pull-up/pull-down resistors cannot
be enabled/disabled and the value of these resistors cannot be programmed. The range of an ipu resistor can be between 26 kΩ–63 kΩ. The
range of an ipd resistor can be between 31 kΩ–85kΩ. The three-state voltage of ipu pads will not reach to the full VDD_EXT level; at typical
conditions the voltage is in the range of 2.3 V to 2.7 V.
In this table, all pins are LVTTL compliant with the exception of the thermal diode pins.
相關PDF資料
PDF描述
VE-2W0-CY-F2 CONVERTER MOD DC/DC 5V 50W
ADSP-2188MBSTZ-266 IC DSP CONTROLLER 16BIT 100LQFP
TAJB105K035H CAP TANT 1UF 35V 10% 1210
MAX31855EASA+ IC CONV THERMOCOUPLE-DGTL 8SOIC
GCC05DRXN CONN EDGECARD 10POS DIP .100 SLD
相關代理商/技術參數
參數描述
ADSP-21489BSWZ-AX 制造商:Analog Devices 功能描述:X GRADE SHARC PROCESSOR - Trays
ADSP-21489BSWZ-BX 制造商:Analog Devices 功能描述:X GRADE SHARC PROCESSOR - Trays
ADSP-21489KSWZ-3A 功能描述:IC CCD SIGNAL PROCESSOR 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21489KSWZ-3B 功能描述:IC CCD SIGNAL PROCESSOR 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21489KSWZ-4A 功能描述:IC CCD SIGNAL PROCESSOR 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*