- 您現在的位置：買賣IC網 > PDF目錄362147 > ADS8402IPFBT 16-BIT, 1.25 MSPS, UNIPOLAR DIFFERENTIAL INPUT, MICRO POWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE AND REFERENCE PDF資料下載
參數資料
| 型號： | ADS8402IPFBT |
| 英文描述： | 16-BIT, 1.25 MSPS, UNIPOLAR DIFFERENTIAL INPUT, MICRO POWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE AND REFERENCE |
| 中文描述： | 16位，1.25 MSPS的，單極差動輸入，微功耗采樣模數位并行接口和參考轉爐 |
| 文件頁數： | 21/25頁 |
| 文件大?。?/td> | 212K |
| 代理商： | ADS8402IPFBT |
ADS8402
SLAS154B
–
DECEMBER 2002
–
REVISED MAY 2003
www.ti.com
21
PRINCIPLES OF OPERATION
The ADS8402 is a high-speed successive approximation register (SAR) analog-to-digital converter (ADC). The
architecture is based on charge redistribution, which inherently includes a sample/hold function. See Figure 32 for
the application circuit for the ADS8402.
The conversion clock is generated internally. The conversion time of 610 ns is capable of sustaining a 1.25-MHz
throughput.
The analog input is provided to two input pins: +IN and
–
IN. When a conversion is initiated, the differential input on
these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected
from any internal function.
REFERENCE
The ADS8402 can operate with an external reference with a range from 2.5 V to 4.2 V. A 4.096-V internal reference
is included. When internal reference is used, pin 2 (REFOUT) should be connected to pin 1 (REFIN) with an 0.1
μ
F
decoupling capacitor and 1
μ
F storage capacitor between pin 2 (REFOUT) and pins 47 and 48 (REFM) (see
Figure 33). The internal reference of the converter is double buffered. If an external reference is used, the second
buffer provides isolation between the external reference and the CDAC. This buffer is also used to recharge all of
the capacitors of the CDAC during conversion. Pin 2 (REFOUT) can be left unconnected (floating) if external
reference is used.
ANALOG INPUT
When the converter enters the hold mode, the voltage difference between the +IN and
–
IN inputs is captured on the
internal capacitor array. Both +IN and
–
IN input has a range of
–
0.2 V to V
ref
+ 0.2 V. The input span
(+IN
–
(
–
IN)) is limited to
–
V
ref
to V
ref
.
The input current on the analog inputs depends upon a number of factors: sample rate, input voltage, and source
impedance. Essentially, the current into the ADS8402 charges the internal capacitor array during the sample period.
After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage
must be able to charge the input capacitance (25 pF) to an 16-bit settling level within the acquisition time (150 ns)
of the device. When the converter goes into the hold mode, the input impedance is greater than 1 G
.
Care must be taken regarding the absolute analog input voltage. To maintain the linearity of the converter, the +IN
and
–
IN inputs and the span (+IN
–
(
–
IN)) should be within the limits specified. Outside of these ranges, the
converter
’
s linearity may not meet specifications. To minimize noise, low bandwidth input signals with low-pass filters
should be used.
Care should be taken to ensure that the output impedance of the sources driving +IN and
–
IN inputs are matched.
If this is not observed, the two inputs could have different setting time. This may result in offset error, gain error and
linearity error which varies with temperature and input voltage.
A typical input circuit using TI
’
s THS4503 is shown in Figure 34. Input from a single-ended source may be converted
into differential signal for ADS8402 as shown in the figure. In case the source itself is differential then THS4503 may
be used in differential input and differential output mode.
相關PDF資料 |
PDF描述 |
|---|---|
| ADS8413IRGZT | 16-BIT, 2-MSPS, LVDS SERIAL INTERFACE, SAR ANALOG-TO-DIGITAL CONVERTER |
| ADS8413IRGZTG4 | 16-BIT, 2-MSPS, LVDS SERIAL INTERFACE, SAR ANALOG-TO-DIGITAL CONVERTER |
| ADS8413IBRGZR | 16-BIT, 2-MSPS, LVDS SERIAL INTERFACE, SAR ANALOG-TO-DIGITAL CONVERTER |
| ADS8413IBRGZRG4 | 16-BIT, 2-MSPS, LVDS SERIAL INTERFACE, SAR ANALOG-TO-DIGITAL CONVERTER |
| ADS8413IBRGZT | 16-BIT, 2-MSPS, LVDS SERIAL INTERFACE, SAR ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS8402IPFBTG4 | 功能描述:模數轉換器 - ADC 16B 1.25MSPS Para ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8405 | 制造商:BB 制造商全稱:BB 功能描述:16-BIT, 1-MSPS, PSEUDO-BIPOLAR, FULLY DIFFERENTIAL INPUT, MICROPOWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE, REFERENCE |
| ADS8405EVM | 功能描述:數據轉換 IC 開發工具 ADS8405 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADS8405IBPFBR | 功能描述:模數轉換器 - ADC 16-Bit 1.25 MSPS Uni Input Micro Pwr Smpl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8405IBPFBRG4 | 功能描述:模數轉換器 - ADC 16-Bit 1.25 MSPS Uni Input Micro Pwr Smpl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。