- 您現在的位置：買賣IC網 > PDF目錄364641 > ADS8371IBPFBR 16BIT 750KHZ UNIPOLAR INPUT, MICRO POWER SAMPLING ANALOG TO DIGITAL CONVERTER WITH PARALLEL INTERFACE PDF資料下載
參數資料
| 型號： | ADS8371IBPFBR |
| 元件分類： | ADC |
| 英文描述： | 16BIT 750KHZ UNIPOLAR INPUT, MICRO POWER SAMPLING ANALOG TO DIGITAL CONVERTER WITH PARALLEL INTERFACE |
| 中文描述： | 16位750kHz的單極性輸入，微功耗采樣模數轉換器并行接口 |
| 文件頁數： | 30/32頁 |
| 文件大小： | 350K |
| 代理商： | ADS8371IBPFBR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁
SLAS390A JUNE 2003 REVISED DECEMBER 2003
www.ti.com
30
LAYOUT
For optimum performance, care should be taken with the physical layout of the ADS8371 circuitry.
As the ADS8371 offers single-supply operation, it will often be used in close proximity with digital logic,
microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the
higher the switching speed, the more difficult it is to achieve good performance from the converter.
The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground
connections and digital inputs that occur just prior to latching the output of the analog comparator. Thus, driving any
single conversion for an n-bit SAR converter, there are at least n
windows
in which large external transient voltages
can affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic,
or high power devices.
The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external
event.
On average, the ADS8371 draws very little current from an external reference as the reference voltage is internally
buffered. If the reference voltage is external and originates from an op amp, make sure that it can drive the bypass
capacitor or capacitors without oscillation. A 0.1-
μ
F bypass capacitor is recommended from pin 1 (REFIN) directly
to pin 48 (REFM). REFM and AGND should be shorted on the same ground plane under the device.
The AGND and BDGND pins should be connected to a clean ground point. In all cases, this should be the analog
ground. Avoid connections which are too close to the grounding point of a microcontroller or digital signal processor.
If required, run a ground trace directly from the converter to the power supply entry point. The ideal layout consists
of an analog ground plane dedicated to the converter and associated analog circuitry.
As with the AGND connections, +VA
should be connected to a 5-V power supply plane or trace that is separate from
the connection for digital logic until they are connected at the power entry point. Power to the ADS8371 should be
clean and well bypassed. A 0.1-
μ
F ceramic bypass capacitor should be placed as close to the device as possible.
See Table 3 for the placement of the capacitor. In addition, a 1-
μ
F to 10-
μ
F capacitor is recommended. In some
situations, additional bypassing may be required, such as a 100-
μ
F electrolytic capacitor or even a Pi filter made up
of inductors and capacitors—all designed to essentially low-pass filter the 5-V supply, removing the high frequency
noise.
Table 3. Power Supply Decoupling Capacitor Placement
POWER SUPPLY PLANE
SUPPLY PINS
CONVERTER ANALOG SIDE
CONVERTER DIGITAL SIDE
Pin pairs that require shortest path to decoupling capacitors
(4,5), (8,9), (10,11), (13,15),
(43,44), (45,46)
(24,25)
Pins that require no decoupling
12, 14
37, 38
相關PDF資料 |
PDF描述 |
|---|---|
| ADS8371IBPFBT | 16BIT 750KHZ UNIPOLAR INPUT, MICRO POWER SAMPLING ANALOG TO DIGITAL CONVERTER WITH PARALLEL INTERFACE |
| ADS8371I | 16BIT 750KHZ UNIPOLAR INPUT, MICRO POWER SAMPLING ANALOG TO DIGITAL CONVERTER WITH PARALLEL INTERFACE |
| ADS8371IPFBR | 16BIT 750KHZ UNIPOLAR INPUT, MICRO POWER SAMPLING ANALOG TO DIGITAL CONVERTER WITH PARALLEL INTERFACE |
| ADS8371IPFBT | 16BIT 750KHZ UNIPOLAR INPUT, MICRO POWER SAMPLING ANALOG TO DIGITAL CONVERTER WITH PARALLEL INTERFACE |
| ADS8380 | 18-BIT, 600-kHz, PSEUDO-DIFFERENTIAL INPUT, MICROPOWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH SERIAL INTERFACE AND REFERENCE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS8371IBPFBRG4 | 功能描述:模數轉換器 - ADC 16-Bit 750kHz Unipol Inp MicroPwr Smplng RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8371IBPFBT | 功能描述:模數轉換器 - ADC 16-Bit 750kHz Unipol Inp MicroPwr Smplng RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8371IBPFBTG4 | 功能描述:模數轉換器 - ADC 16-Bit 750kHz Unipol Inp MicroPwr Smplng RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8371IPFBR | 功能描述:模數轉換器 - ADC 16-Bit 750kHz Unipol Inp MicroPwr Smplng RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8371IPFBRG4 | 功能描述:模數轉換器 - ADC 16-Bit 750kHz Unipol Inp MicroPwr Smplng RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。