- 您現在的位置：買賣IC網 > PDF目錄375265 > ADS7852 12-Bit, 8-Channel, Parallel Output ANALOG-TO-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS7852 |
| 英文描述： | 12-Bit, 8-Channel, Parallel Output ANALOG-TO-DIGITAL CONVERTER |
| 中文描述： | 12位，8通道，并行輸出的模擬數字轉換器 |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 148K |
| 代理商： | ADS7852 |
13
ADS7852
In addition to using the address pins in conjunction with RD,
the power-down mode can also be terminated implicitly by
starting a new conversion (e.g., taking WR LOW while CS
is LOW). If it is desired to keep the ADS7852 in a power-
down state for a period that is greater than dictated by the
sampling rate, the convert signal driving the WR pin must be
disabled.
The typical supply current of the ADS7852, with a 5V
supply and a 500kHz sampling rate, is 2.6mA. In the Nap
mode, the typical supply current is 600
μ
A. In the Sleep
mode, the current is typically reduced to 10
μ
A.
LAYOUT
For optimum performance, care should be taken with the
physical layout of the ADS7852 circuitry. This is particu-
larly true if the CLK input is approaching the maximum
throughput rate.
The basic SAR architecture is sensitive to glitches or sudden
changes on the power supply, reference, ground connections
and digital inputs that occur just prior to latching the output
of the analog comparator. Thus, driving any single conver-
sion for an n-bit SAR converter, there are n “windows” in
which large external transient voltages can affect the conver-
sion result. Such glitches might originate from switching
power supplies, nearby digital logic, or high power devices.
The degree of error in the digital output depends on the
reference voltage, layout, and the exact timing of the exter-
nal event. Their error can change if the external event
changes in times with respect to the CLK input.
With this in mind, power to the ADS7852 should be clean
and well bypassed. A 0.1
μ
F ceramic bypass capacitor should
be placed as close to the device as possible. In addition, a
1
μ
F to 10
μ
F capacitor is recommended. If needed an even
larger capacitor and a 5
or 10
series resistor may be used
to low pass filter a noisy supply. The ADS7852 draws very
little current from an external reference on average as the
reference voltage is internally buffered. However, glitches
from the conversion process appear at the V
REF
input and the
reference source must be able to handle this. Whether the
reference is internal or external, the V
REF
pin should be
bypassed with a 0.1
μ
F capacitor. An additional larger ca-
pacitor may also be used, if desired. If the reference voltage
is external and originates from an op amp, make sure it can
drive the bypass capacitor or capacitors without oscillation.
The GND pin should be connected to a clean ground point. In
many cases, this will be the “analog” ground. Avoid connec-
tions which are too near the grounding point of a microcontroller
or digital signal processor. If needed, run a ground trace
directly from the converter to the power supply entry point.
The ideal layout will include an analog ground plane dedicated
to the converter and associated analog circuitry.
FIGURE 5. Timing Diagram and Test Circuits for Param-
eters in Figure 2.
Voltage Waveforms for t
dis
Load Circuit for t
dis
and t
en
D
OUT
Test Point
t
dis
Waveform 2, t
en
V
CC
t
dis
Waveform 1
100pF
C
LOAD
3k
t
dis
CS/SHDN
D
OUT
Waveform 1
(1)
D
OUT
Waveform 2
(2)
90%
10%
V
IH
NOTES: (1) Waveform 1 is for an output with internal
conditions such that the output is HIGH unless disabled
by the output control. (2) Waveform 2 is for an output
with internal conditions such that the output is LOW
unless disabled by the output control.
相關PDF資料 |
PDF描述 |
|---|---|
| ADS7852Y | CMOS 8-Stage Presettable 8-Bit Binary Synchronous Down Counter 16-CDIP -55 to 125 |
| ADS7861 | CMOS 8-Stage Presettable 8-Bit Binary Synchronous Down Counter 16-CDIP -55 to 125 |
| ADS7861E | CMOS 4-Bit-by-16-Word FIFO Register 16-PDIP -55 to 125 |
| ADS7861EB | CMOS 4-Bit-by-16-Word FIFO Register 16-PDIP -55 to 125 |
| ADS801 | 12-Bit, 25MHz Sampling ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7852Y | 制造商:Texas Instruments 功能描述:12BIT ADC PARALLEL O/P SMD 7852 制造商:Texas Instruments 功能描述:12BIT ADC, PARALLEL O/P, SMD, 7852 制造商:Texas Instruments 功能描述:12BIT ADC, PARALLEL O/P, SMD, 7852; Resolution (Bits):12bit; Sampling Rate:500kSPS; Supply Voltage Type:Single; Supply Voltage Min:4.75V; Supply Voltage Max:5.25V; Supply Current:2.6mA; Digital IC Case Style:TQFP; No. of Pins:32; |
| ADS7852Y/250 | 功能描述:模數轉換器 - ADC 12-Bit 8-Channel Parallel Output RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7852Y/250G4 | 功能描述:模數轉換器 - ADC 12-Bit 8-Channel Parallel Output RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7852Y/2K | 功能描述:模數轉換器 - ADC 12-Bit 8-Channel Parallel Output RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7852Y/2KG4 | 功能描述:模數轉換器 - ADC 12-Bit 8-Channel Parallel Output RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。