- 您現在的位置：買賣IC網 > PDF目錄10395 > ADS7812PBG4 (Texas Instruments)IC 12BIT 35MW SER OUT ADC 16DIP PDF資料下載
參數資料
| 型號： | ADS7812PBG4 |
| 廠商： | Texas Instruments |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 12BIT 35MW SER OUT ADC 16DIP |
| 產品培訓模塊： | Data Converter Basics |
| 標準包裝： | 25 |
| 位數： | 12 |
| 采樣率（每秒）： | 40k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 35mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 3 個單端，單極；3 個單端，雙極 |
ADS7812
15
SBAS042A
www.ti.com
LAYOUT
The ADS7812 should be treated as a precision analog
component and should reside completely on the “analog”
portion of the printed circuit board. Ideally, a ground plane
should extend underneath the ADS7812 and under all other
analog components. This plane should be separate from the
digital ground until they are joined at the power supply
connection. This will help prevent dynamic digital ground
currents from modulating the analog ground through a
common impedance to power ground.
The +5V power should be clean, well-regulated, and sepa-
rate from the +5V power for the digital portion of the design.
One possibility is to derive the +5V supply from a linear
regulator located near the ADS7812. If derived from the
digital +5V power, a 5
to 10 resistor should be placed in
series with the power connection from the digital supply. It
may also be necessary to increase the bypass capacitance
near the VS pin (an additional 100F or greater capacitor in
parallel with the 10
F and 0.1F capacitors). For designs
with a large number of digital components or very high
speed digital logic, this simple power supply filtering scheme
may not be adequate.
SENSITIVITY TO EXTERNAL
DIGITAL SIGNALS
All successive approximation register-based A/D converters
are sensitive to external sources of noise. The reason for this
will be explained in the following paragraphs. For the
ADS7812 and similar A/D converters, this noise most often
originates due to the transition of external digital signals.
While digital signals that run near the converter can be the
source of the noise, the biggest problem occurs with the
digital inputs to the converter itself.
In many cases, the system designer may not be aware that
there is a problem or a potential for a problem. For a 12-bit
system, these problems typically occur at the least significant
bits and only at certain places in the converter’s transfer
function. For a 16-bit converter, the problem can be much
easier to spot.
For example, the timing diagram in Figure 2 shows that the
CONV signal should return HIGH sometime during time t2.
In fact, the CONV signal can return HIGH at any time
during the conversion. However, after time t2, the transition
of the CONV signal has the potential of creating a good deal
of noise on the ADS7812 die. If this transition occurs at just
precisely the wrong time, the conversion results could be
affected. In a similar manner, transitions on the DATACLK
input could affect the conversion result.
For the ADS7812, there are 12 separate bit decisions which
are made during the conversion. The most significant bit
decision is made first, proceeding to the least significant bit
at the end of the conversion. Each bit decision involves the
assumption that the bit being tested should be set. This is
combined with the result that has been achieved so far. The
converter compares this combined result with the actual
input voltage. If the combined result is too high, the bit is
cleared. If the result is equal to or lower than the actual input
voltage, the bit remains HIGH. This is why the basic
architecture is referred to as “successive approximation
register.”
If the result so far is getting very close to the actual input
voltage, then the comparison involves two voltages which are
very close together. The ADS7812 has been designed so that
the internal noise sources are a minimum just prior to the
comparator result being latched. However, if a external digital
signal transitions at this time, a great deal of noise will be
coupled into the sensitive analog section of the ADS7812.
Even if this noise produces a difference between the two
voltages of only 2mV, the conversion result will be off by 3
counts or least significant bits (LSBs). (The internal LSB size
of the ADS7812 is 610
V regardless of the input range.)
Once a digital transition has caused the comparator to make
a wrong bit decision, the decision cannot be corrected. All
subsequent bit decisions will then be wrong (unless some
type of error correction is employed). Figure 13 shows a
successive approximation process that has gone awry. The
dashed line represents what the correct bit decisions should
have been. The solid line represents the actual result of the
conversion.
FIGURE 13. SAR Operation When External Noise Affects the Conversion.
1
t
Converter’s
Full-Scale
Input Voltage
Range
0
Conversion Clock
Incorrect Result
Correct Result
Actual Input
Voltage
Internal DAC
Voltage
Wrong Bit Decision Made Here
Proper SAR Operation
SAR Operation after
Wrong Bit Decision
1
(1
1)
0
1
0
External Noise
Conversion Start
(Hold Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J5P-MY-B1 | CONVERTER MOD DC/DC 13.8V 50W |
| ADS7812PB | IC 12-BIT 35MW SER OUT A/D 16DIP |
| VI-J5M-MY-B1 | CONVERTER MOD DC/DC 10V 50W |
| LLM31MR71A225MA01L | CAP CER 2.2UF 10V 20% X7R 1206 |
| MS27467T15B19B | CONN HSG PLUG 19POS STRGHT SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7812PG4 | 功能描述:模數轉換器 - ADC Low-Power Serial 12-Bit Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7812U | 功能描述:模數轉換器 - ADC Low-Power Serial 12-Bit Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7812U | 制造商:Texas Instruments 功能描述:A/D Converter (A-D) IC 制造商:Texas Instruments 功能描述:IC, ADC, 12BIT, 40KSPS, SOIC-16 |
| ADS7812U/1K | 功能描述:模數轉換器 - ADC Low-Pwr Serial 12B Sampling ADC Cnvrtr RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7812U/1KE4 | 功能描述:模數轉換器 - ADC Low-Power Serial 12-Bit Sampling RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。