- 您現在的位置：買賣IC網 > PDF目錄362144 > ADS7803BN Autocalibrating, 4-Channel, 12-Bit ANALOG-TO-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS7803BN |
| 英文描述： | Autocalibrating, 4-Channel, 12-Bit ANALOG-TO-DIGITAL CONVERTER |
| 中文描述： | Autocalibrating，4通道，12位模擬數字轉換器 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 99K |
| 代理商： | ADS7803BN |
ADS7803
6
STARTING A CONVERSION
A conversion is initiated on the rising edge of the WR input,
with valid signals on A0, A1 and CS. The selected input
channel is sampled for five clock cycles. The successive
approximation conversion takes place during clock cycles 6
through 17.
Figures 2 and 3 show the full conversion sequence and the
timing to initiate a conversion.
A conversion can also be initiated by a rising edge on pin 26,
if a HIGH has been written to D2 of the Special Function
Register, as discussed below.
CALIBRATION
A calibration cycle is initiated automatically upon power-up
(or after a power failure). Calibration can also be initiated by
the user at any time by the rising edge of a minimum 100ns-
wide LOW pulse on the CAL pin (pin 26), or by setting D1
HIGH in the Special Function Register (see SFR section).
A calibration command will initiate a calibration cycle,
regardless of whether a conversion is in process. During a
calibration cycle, convert commands are ignored.
Calibration takes 168 clock cycles, and a normal conversion
(17 clock cycles) is added automatically. Thus, at the end of
a calibration cycle, there is valid conversion data in the
output registers. For maximum accuracy, the supplies and
reference need to be stable during the calibration procedure.
To ensure that supply voltages have settled and are stable, an
internal timer provides a waiting period of 42,425 clock
cycles between power-up/power-failure and the start of the
calibration cycle.
PIN #
NAME
DESCRIPTION
1
SFR
Special Function Register. When connected to a microprocessor address pin, allows access to special functions
through D0 to D7. See the sections discussing the Special Function Register. If not used, connect to DGND. This pin
has an internal pull-down.
2 to 5
AIN0 to AIN3
Analog inputs. Channel 0 to channel 3.
6
V
REF
+
Positive voltage reference input. Normally +5V. Must be
≤
V
A
.
7
V
REF
–
Negative voltage reference input. Normally 0V.
8
DGND
Digital ground. DGND = 0V.
9
V
D
Logic supply voltage. V
D
= +5V. Must be
≤
V
A
and applied after V
A
.
10 to 17
D0 to D7
Data Bus Input/Output Pins. Normally used to read output data. See section on SFR (Special Function Register) for
other uses.
When SFR is LOW, these function as follows:
Data Bit 7 if HBE is LOW; if HBE is HIGH, acts as converter status pin and is HIGH during conversion or calibration,
goes LOW after the conversion is completed. (Acts as an inverted BUSY).
Data Bit 6 if HBE is LOW; LOW if HBE is HIGH.
Data Bit 5 if HBE is LOW; LOW if HBE is HIGH.
Data Bit 4 if HBE is LOW; LOW if HBE is HIGH.
Data Bit 3 if HBE is LOW; Data Bit 11 (MSB) if HBE is HIGH.
Data Bit 2 if HBE is LOW; Data Bit 10 if HBE is HIGH.
Data Bit 1 if HBE is LOW; Data Bit 9 if HBE is HIGH.
Data Bit 0 (LSB) if HBE is LOW; Data Bit 8 if HBE is HIGH.
10
D7
11
12
13
14
15
16
17
D6
D5
D4
D3
D2
D1
D0
18
RD
Read Input. Active LOW; used to read the data outputs in combination with CS and HBE.
19
CS
Chip Select Input. Active LOW.
20
WR
Write Input. Active LOW; used to start a new conversion and to select an analog channel via address inputs A0 and A1
in combination with CS. The minimum WR pulse LOW width is 100ns.
21
HBE
High Byte Enable. Used to select high or low data output byte in combination with CS and RD, or to select SFR.
22
BUSY
BUSY is LOW during conversion or calibration. BUSY goes HIGH after the conversion is completed.
23
CLK
Clock Input. For internal or external clock operation. For external clock operation, connect pin 23 to a 74HC-compatible
clock source. For internal clock operation, connect pin 23 per the clock operation description.
24 to 25
A0 to A1
Address Inputs. Used to select one of four analog input channels in combination with CS and WR. The address inputs
are latched on the rising edge of WR or CS.
A1
A0
Selected Channel
LOW
LOW
HIGH
HIGH
LOW
HIGH
LOW
HIGH
AIN0
AIN1
AIN2
AIN3
26
CAL
(SHC)
Calibration Input. A calibration cycle is initiated when CAL is LOW. The minimum pulse width of CAL is 100ns. If not
used, connect to V
D
. In this case calibration is only initiated at power on, or with SFR. If D2 of the SFR is programmed
HIGH, pin 26 will be used as an input to control the sample-to-hold timing. A rising edge on pin 26 will switch from
sample-mode to hold-mode and initiate a conversion. This pin has an internal pull-up.
27
AGND
Analog Ground. AGND = 0V.
28
V
A
Analog Supply. V
A
= +5V. Must be
≥
V
D
and V
REF
+.
PIN ASSIGNMENTS
相關PDF資料 |
PDF描述 |
|---|---|
| ADS7803BP | Autocalibrating, 4-Channel, 12-Bit ANALOG-TO-DIGITAL CONVERTER |
| ADS7807UBE4 | Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS7807UBG4 | Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS7807UE4 | Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS7807PBG4 | Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7803BP | 制造商:BB 制造商全稱:BB 功能描述:Autocalibrating, 4-Channel, 12-Bit ANALOG-TO-DIGITAL CONVERTER |
| ADS7804 | 制造商:BB 制造商全稱:BB 功能描述:12-Bit 10ms Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS7804P | 功能描述:模數轉換器 - ADC 12-Bit 10us Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7804PB | 功能描述:模數轉換器 - ADC 12-Bit 10us Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7804PBG4 | 功能描述:模數轉換器 - ADC 12B 10us Sampling CMOS ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。