- 您現在的位置：買賣IC網 > PDF目錄374021 > ADP3333ARM-315 (Analog Devices, Inc.) Single-Cell Li-Ion and Li-Pol Battery Gas Gauge IC with I<sup>2</sup>C Interface 10-VSON -20 to 70 PDF資料下載
參數資料
| 型號： | ADP3333ARM-315 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Single-Cell Li-Ion and Li-Pol Battery Gas Gauge IC with I<sup>2</sup>C Interface 10-VSON -20 to 70 |
| 中文描述： | 高精度超低智商，300毫安，anyCAP低壓差穩壓器 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 119K |
| 代理商： | ADP3333ARM-315 |
REV. 0
ADP3333
–7–
Calculating Junction T emperature
Device power dissipation is calculated as follows:
(
Where
I
LOAD
and
I
GND
are load current and ground current,
V
IN
and
V
OUT
are the input and output voltages respectively.
Assuming the worst-case operating conditions are I
LOAD
=
300 mA, I
GND
= 2.6 mA, V
IN
= 4.0 V and V
OUT
= 3.0 V, the
device power dissipation is:
(
T he package used on the ADP3333 has a thermal resistance of
158
°
C/W for 4-layer boards. T he junction temperature rise
above ambient will be approximately equal to:
P
V
V
I
V
I
D
IN
OUT
LOAD
IN
GND
=
)
+
(
)
P
V
V
mA
V
mA
mW
D
=
)
+
(
)
=
4 0
.
3 0
.
300
4 2
.
2 0
.
308
T
W
C W
°
C
A
J
=
×
=
°
0 308
.
158
48 7
/
.
So, to limit the junction temperature to 125
°
C, the maximum
allowable ambient temperature is:
T
C
C
C
MAX
A
(
)
.
.
=
°
°
=
°
125
48 7
76 3
Shutdown Mode
Applying a high signal to the shutdown pin, or connecting it to
the input pin, will turn the output ON. Pulling the shutdown
pin to 0.3 V or below, or connecting it to ground, will turn the
output OFF. In shutdown mode, the quiescent current is reduced
to less than 1
μ
A.
Printed Circuit Board Layout Considerations
Use the following general guidelines when designing printed
circuit boards:
1. K eep the output capacitor as close to the output and ground
pins as possible.
2. K eep the input capacitor as close to the input and ground
pins as possible.
3. PC board traces with larger cross sectional areas will remove
more heat from the ADP3333. For optimum heat transfer,
specify thick copper and use wide traces.
4. Connect the NC pins (Pins 5, 6, and 8) to ground for better
thermal performance.
5. T he thermal resistance can be decreased by approximately
10% by adding a few square centimeters of copper area to
the lands connected to the pins of the LDO.
6. Use additional copper layers or planes to reduce the thermal
resistance. Again, connecting the other layers to the ground and
NC pins of the ADP3333 is best, but not necessary. When
connecting the ground pad to other layers use multiple vias.
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3333ARM-33 | Single-Cell Li-Ion and Li-Pol Battery Gas Gauge IC with I<sup>2</sup>C Interface 10-VSON -20 to 70 |
| ADP3333ARM-5 | Li-Ion and Li-Pol Battery Gas Gauge IC for Portable Applications (bqJUNIOR) 10-VSON -20 to 70 |
| ADP3333 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADP3334 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADP3334AR | Replaced by BQ27541 : Single Cell Li-Ion Battery Manager with Impedance Track Fuel Gauge Technology 20-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP3333ARM-33 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Accuracy Ultralow IQ, 300 mA, anyCAP Low Dropout Regulator |
| ADP3333ARM-3-R7 | 制造商:Analog Devices 功能描述: |
| ADP3333ARM-3-REEL | 功能描述:IC REG LDO 3V .3A 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:anyCAP® 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.3V 輸入電壓:2.5 V ~ 5.5 V 電壓 - 壓降（標準）:0.1V @ 200mA 穩壓器數量:2 電流 - 輸出:300mA 電流 - 限制（最?。?350mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-UFQFN 供應商設備封裝:8-MLPQ-UT（1.5x1.5） 包裝:剪切帶 (CT) 產品目錄頁面:1358 (CN2011-ZH PDF) 其它名稱:SC560HULCT |
| ADP3333ARM-3-REEL7 | 制造商:Analog Devices 功能描述:LDO Regulator Pos 3V 0.6A 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:300MA FIXED ANYCAP LDO - Tape and Reel |
| ADP3333ARM-5 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Accuracy Ultralow IQ, 300 mA, anyCAP Low Dropout Regulator |
發布緊急采購，3分鐘左右您將得到回復。