- 您現在的位置：買賣IC網 > PDF目錄57600 > ADP12423 GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-14.22Psi, 0-100mV, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | ADP12423 |
| 元件分類： | 壓力傳感器 |
| 英文描述： | GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-14.22Psi, 0-100mV, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | DIP-6 |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 175K |
| 代理商： | ADP12423 |
PF (ADP1)
NOTES
1. Mounting
Use lands on the printed-circuit boards to
which the sensor can be securely fixed.
2. Soldering
1) Due to its small size, the thermal
capacity of the pressure sensor DIP type
is low. Therefore, take steps to minimize
the effects of external heat.
Dip soldering bath: Max. 260°C 500°F, 5
sec.
Soldering iron: 260 to 300°C 500 to
572°F (30W) within 5 sec.
2) Use a non-corrosive resin type of flux.
Since the pressure sensor DIP type is
exposed to the atmosphere, do not allow
flux to enter inside.
3. Cleaning
1) Since the pressure sensor chip is
exposed to the atmosphere, do not allow
cleaning fluid to enter inside.
2) Avoid ultrasonic cleaning since this
may cause breaks or disconnections in
the wiring.
4. Environment
Consult with us before using or storing
the pressure sensor chip in a place
exposed to corrosive gases (such as the
gases given off by organic solvents, sul-
fites, hydrogen sulfides, etc.) which will
adversely affect the performance of the
pressure sensor chip.
5. Quality check under actual loading
conditions
1) To assure reliability, check the sensor
under actual loading conditions. Avoid
any situation that may adversely affect
its performance.
2) As for test data, please contact us.
6. Other handling precautions
1) That using the wrong pressure range
or mounting method may result in acci-
dents.
2) Air can be used directly as a pressure
medium. Consult with us before using a
corrosive gas (such as a gas given off by
an organic solvent, sulfite or hydrogen
sulfide) as the pressure medium.
3) The pressure sensor chip is posi-
tioned inside the pressure inlet. Never
poke wires or other foreign matter
through the pressure inlet since they
may damage the chip or block the inlet.
Avoid use when the atmospheric pres-
sure inlet is blocked.
4) Leave pin No. 4 unconnected since
the pressure sensor chip may be dam-
aged if a voltage is applied to this pin.
5) Use an operating pressure which is
within the rated pressure range. Using a
pressure beyond this range may cause
damage.
6) Since this pressure sensor chip does
not have a water-proof construction, con-
sult with us if it is to be used in a location
where it may be sprayed with water, etc.
7) Avoid using the pressure sensor chip
in an environment where condensation
may form. Furthermore, its output may
fluctuate if any moisture adhering to it
freezes.
8) The pressure sensor chip is construct-
ed in such a way that its output will fluc-
tuate when it is exposed to light.
Especially when pressure is to be
applied by means of a transparent tube,
take steps to prevent the pressure sen-
sor chip from being exposed to light.
9) Avoid using the pressure sensor chip
where it will be susceptible to ultrasonic
or other high-frequency vibration.
10) Since static charge can damage the
pressure sensor chip, bear in mind the
following handling precautions.
When storing the pressure sensor
chips, use a conductive material to
short the pins or wrap the entire chip in
aluminum foil. Plastic containers
should not be used to store or transport
the chips since they readily become
charged.
When using the pressure sensor chips,
all the charged articles on the bench
surface and the work personnel should
be grounded so that any ambient static
will be safely discharged.
11) Due to the pressures involved, give
due consideration to the securing of the
pressure sensor DIP type and to the
securing and selection of the inlet tube.
Consult us if you have any queries.
APPLICATION CIRCUIT
DIAGRAM (EXAMPLE)
The pressure sensor is designed to con-
vert a voltage by means of constant cur-
rent drive and then, if necessary, it
amplifies the voltage for use. The circuit
shown below is a typical example of a
circuit in which the pressure sensor is
used.
OP
AMP
OP
AMP
OP
AMP
Constant current
circuit unit
Pressure
sensor
Amplifier circuit unit
MOUNTING METHOD
The general method for transmitting air
pressures differs depending on whether
the pressure is low or high.
Checkpoints for use
<1> Select a pressure inlet pipe which is
sturdy enough to prevent pressure
leaks.
<2> Fix the pressure inlet pipe securely
so as to prevent pressure leaks.
<3> Do not block the pressure inlet pipe.
Methods of transmitting air pressures
When the pressure
is low
When the pressure
is high
(4.9 to 98.1 kPa)
(196.1 to 980.7 kPa)
If a tube is used as the pressure inlet pipe,
it may become disengaged. Therefore, use
a sturdy tube and secure it using O-rings.
Tube
Printed-
circuit
board
Printed-
circuit
board
O-ring
Pressure
inlet pipe
PF PRESSURE SENSOR
2004.11.1 7:04 PM
Page 41
相關PDF資料 |
PDF描述 |
|---|---|
| ADP12723 | GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-71.11Psi, 0-100mV, RECTANGULAR, THROUGH HOLE MOUNT |
| ADP11113 | GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-21.32Psi, 0-100mV, RECTANGULAR, THROUGH HOLE MOUNT |
| ADP1191 | GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-142.23Psi, 0-100mV, RECTANGULAR, THROUGH HOLE MOUNT |
| ADP1211 | GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-21.32Psi, 0-100mV, RECTANGULAR, THROUGH HOLE MOUNT |
| ADP12A1 | GAGE, STRAIN GUAGE PRESSURE SENSOR, 0-5.8Psi, 0-43.50mV, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP124-3.3-EVALZ | 功能描述:BOARD EVALUATION 3.3V ADP124 RoHS:是 類別:編程器，開發系統 >> 評估板 - 線性穩壓器 (LDO) 系列:- 產品變化通告:1Q2012 Discontinuation 30/Mar/2012 設計資源:NCP590MNDPTAGEVB Gerber Files 標準包裝:1 系列:- 每 IC 通道數:2 - 雙 輸出電壓:1.8V，2.8V 電流 - 輸出:300mA 輸入電壓:2.1 ~ 5.5 V 穩壓器類型:正，固定式 工作溫度:-40°C ~ 85°C 板類型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名稱:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ADP124ACPZ-1.8-R7 | 功能描述:IC REG LDO 1.8V .5A 8LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:45 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:5V 輸入電壓:6 V ~ 30 V 電壓 - 壓降（標準）:0.47V @ 250mA 穩壓器數量:1 電流 - 輸出:250mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 產品目錄頁面:1289 (CN2011-ZH PDF) 其它名稱:*LP2954AIT*LP2954AIT/NOPBLP2954AIT |
| ADP124ACPZ-2.8-R7 | 功能描述:IC REG LDO 2.8V .5A 8LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:45 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:5V 輸入電壓:6 V ~ 30 V 電壓 - 壓降（標準）:0.47V @ 250mA 穩壓器數量:1 電流 - 輸出:250mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 產品目錄頁面:1289 (CN2011-ZH PDF) 其它名稱:*LP2954AIT*LP2954AIT/NOPBLP2954AIT |
| ADP124ACPZ-2.9-R7 | 功能描述:IC REG LDO 2.9V .5A 8LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:45 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:5V 輸入電壓:6 V ~ 30 V 電壓 - 壓降（標準）:0.47V @ 250mA 穩壓器數量:1 電流 - 輸出:250mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 產品目錄頁面:1289 (CN2011-ZH PDF) 其它名稱:*LP2954AIT*LP2954AIT/NOPBLP2954AIT |
| ADP124ACPZ-3.0-R7 | 功能描述:IC REG LDO 3V .5A 8LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:45 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:5V 輸入電壓:6 V ~ 30 V 電壓 - 壓降（標準）:0.47V @ 250mA 穩壓器數量:1 電流 - 輸出:250mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 產品目錄頁面:1289 (CN2011-ZH PDF) 其它名稱:*LP2954AIT*LP2954AIT/NOPBLP2954AIT |
發布緊急采購，3分鐘左右您將得到回復。