- 您現在的位置：買賣IC網 > PDF目錄352486 > ADP1110AR-33 (Analog Devices, Inc.) Circular Connector Cable Assembly; Connector Type A:Circular Plug; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | ADP1110AR-33 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector Cable Assembly; Connector Type A:Circular Plug; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes |
| 中文描述： | 微功耗，降壓型開關穩壓器，可調節和固定3.3伏，5伏，12伏 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 418K |
| 代理商： | ADP1110AR-33 |
ADP1110
–11–
REV. 0
POSITIVE-TO-NEGATIVE CONVERSION
The ADP1110 can convert a positive input voltage to a negative
output voltage as shown in Figure 23. This circuit is essentially
identical to the step-down application of Figure 19, except that
the “output” side of the inductor is connected to power ground.
When the ADP1110’s internal power switch turns off, current
flowing in the inductor forces the output (–VOUT) to a negative
potential. The ADP1110 will continue to turn the switch on
until its FB pin is 220 mV above its GND pin, so the output
voltage is determined by the formula:
VOUT = 220 mV 1+
R1
R2
ILIM
VIN
SW1
SW2
FB
GND
SET
AO
ADP1110
NC
L1
CL
R1
R2
D1
1N5818
OUTPUT
CINPUT
RLIM
INPUT
6
7
8
1
2
4
5
3
NEGATIVE
OUTPUT
Figure 23. A Positive-to-Negative Converter
The design criteria for the step-down application also apply to
the positive-to-negative converter. The output voltage should be
limited to |6.2 V| unless a diode is inserted in series with the
SW2 pin (see Figure 21.) Also, D1 must again be a Schottky
diode to prevent excessive power dissipation in the ADP1110.
NEGATIVE-TO-POSITIVE CONVERSION
The circuit of Figure 24 converts a negative input voltage to a
positive output voltage. Operation of this circuit configuration is
similar to the step-up topology of Figure 19, except the current
through feedback resistor R1 is level-shifted below ground by a
PNP transistor. The voltage across R1 is VOUT – VBEQ1. However,
diode D2 level-shifts the base of Q1 about 0.6 V below ground
thereby cancelling the VBE of Q1. The addition of D2 also reduces
the circuit’s output voltage sensitivity to temperature, which other-
wise would be dominated by the –2 mV VBE contribution of Q1.
The output voltage for this circuit is determined by the formula:
VOUT = 220 mV
R1
R2
Unlike the positive step-up converter, the negative-to-positive
converter’s output voltage can be either higher or lower than the
input voltage.
ILIM
VIN
SW1
SW2
FB
GND
SET
AO
ADP1110
NC
L1
CL
R2
D1
CINPUT
RLIM
6
7
8
1
2
4
5
3
POSITIVE
OUTPUT
10K
NEGATIVE
INPUT
Q1
2N3906
D2
1N4148
R1
Figure 24. A Negative-to-Positive Converter
LIMITING THE SWITCH CURRENT
The ADP1110’s RLIM pin permits the switch current to be
limited with a single resistor. This current limiting action occurs
on a pulse by pulse basis. This feature allows the input voltage
to vary over a wide range without saturating the inductor or
exceeding the maximum switch rating. For example, a particular
design may require peak switch current of 800 mA with a 2.0 V
input. If VIN rises to 4 V, however, the switch current will
exceed 1.6 A. The ADP1110 limits switch current to 1.5 A and
thereby protects the switch, but the output ripple will increase.
Selecting the proper resistor will limit the switch current to
800 mA, even if VIN increases. The relationship between RLIM
and maximum switch current is shown in Figure 6.
The ILIM feature is also valuable for controlling inductor current
when the ADP1110 goes into continuous-conduction mode.
This occurs in the step-up mode when the following condition is
met:
VOUT +VD IODE
V IN – V SW
<
1
1– DC
where DC is the ADP1110’s duty cycle. When this relationship
exists, the inductor current does not go all the way to zero
during the time that the switch is OFF. When the switch turns
on for the next cycle, the inductor current begins to ramp up
from the residual level. If the switch ON time remains constant,
the inductor current will increase to a high level (see Figure 25).
This increases output ripple and can require a larger inductor
and capacitor. By controlling switch current with the ILIM
resistor, output ripple current can be maintained at the design
values. Figure 26 illustrates the action of the ILIM circuit.
10
0%
100
90
10s
10mV
200mA/div.
Figure 25. ILIM Operation—IL Characteristic
10
0%
100
90
10s
10mV
200mA/div.
Figure 26. ILIM Operation—IL Characteristic
相關PDF資料 |
PDF描述 |
|---|---|
| ADP1110AR-5 | Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes |
| AD7467BRM | 1.8 V, Micro-Power, 8/10/12-Bit ADCs in 6 Lead SOT-23 |
| AD584JN | Pin Programmable Precision Voltage Reference |
| AD584LH | Pin Programmable Precision Voltage Reference |
| AD581UH | High Precision 10 V IC Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP1110AR-5 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Micropower, Step-Up/Step-Down Switching Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
| ADP1110AR-REEL7 | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ADP1111 | 功能描述:板上安裝壓力/力傳感器 14.7kPa 0.15kgf/cm Pressure Sensor RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| ADP1111_09 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Micropower, Step-Up/Step-Down SW Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V |
| ADP1111AN | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:MICROPOWER STEP-UP/DOWN SWITCHING REG. - Bulk 制造商:Analog Devices 功能描述:IC SWITCHING REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。