- 您現在的位置：買賣IC網 > PDF目錄374016 > ADM9240 (Analog Devices, Inc.) Low Cost Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | ADM9240 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Cost Microprocessor System Hardware Monitor |
| 中文描述： | 低成本的微處理器系統硬件監視器 |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 280K |
| 代理商： | ADM9240 |
ADM9240
–10–
REV. 0
SE T T ING OT HE R INPUT RANGE S
If any of the inputs is unused, and there is a requirement for
monitoring another power supply such as –12 V, the input range
of the unused input can easily be scaled and offset to accommo-
date this. For example, if only one processor core voltage is to
be monitored, the unused V
CCP
input can be used to monitor
another supply voltage.
If the voltage to be monitored is positive, it is simply a matter of
using an input with a lower full scale than the voltage to be
measured and adding an external input attenuator, but bear in
mind that the input resistance (
≈
140 k
) of the on-chip attenua-
tor will load the external attenuator. T his can be accounted for
in the calculation, but the values of the on-chip attenuator resis-
tors are not precise and vary with temperature. T herefore, the
external attenuator should have a much lower output resistance
to minimize the loading. If this is not acceptable, a buffer ampli-
fier can be used.
If the input voltage range is negative, it must first be converted
to a positive voltage. T he simplest way to do this is simply to
attenuate and offset the voltage, as shown in Figure 4, which
shows the +V
CCP2
input scaled to measure a –12 V input. Using
the values shown, the input range is zero to –13.5 V, which will
accommodate a +12.5% tolerance on the nominal value.
R1
2.7k
V
R2
1k
V
–13.2V TO 0V IN
+V
CCP2
<
140k
V
R3
39k
V
0V TO 3.6V
+5V
Figure 4. Scaling V
CCP2
to –12 V (+10%)
T he resistor ratios are calculated as follows:
R
1/
R
2 = |
V
–|(
max
)/
V
+
(to give zero volts at the input for the most negative value of V–.
R
2 has no effect under this condition as the voltage across it is
zero)
and:
(
V
+ –
V
FS
)/
V
FS
=
R
2/
R
P
=
(
R
1
and
R
2
in Parallel
)
(to give a voltage
V
FS
at the input when V– is zero, where
V
FS
is
the normal full-scale voltage of the input used).
T his is a simple and cheap solution, but the following points
should be noted.
1. Since the input signal is not inverted, an increase in the mag-
nitude of the –12 V supply (going more negative), will cause
the input voltage to fall and give a lower output code from
the ADC. Conversely, a decrease in the magnitude of the
–12 V supply will cause the ADC code to increase. T his
means that the upper and lower limits will be transposed.
2. Since the offset voltage is derived from the +5 V supply,
variations in this supply will affect the ADC code.
It is therefore a good idea to read the value of the +5 V sup-
ply and adjust the limits for the –12 V supply accordingly.
T he 5 V supply is attenuated by a factor R
P
/(R2+R
P
), where
R
P
is the parallel combination of R1 and R3. An increase in
the 5 V supply increases the ADC input by the DV
×
R
P
/
(R2+R
P
), while a decrease in the 5 V supply correspondingly
decreases the input to the ADC.
3. T he on-chip input attenuators will load the external attenua-
tor, as mentioned earlier.
T his technique can be applied to any other unused input. By
suitable choice of V+ and the input resistors, a variety of nega-
tive and/or bipolar input ranges can be obtained.
T E MPE RAT URE ME ASURE ME NT SY ST E M
T he ADM9240 contains an on-chip bandgap temperature sen-
sor. T he on-chip ADC performs 9-bit conversions on the output
of this sensor and outputs the temperature data in 9-bit twos
complement format, but only the eight most significant bits are
used for temperature limit comparison. T he full 9-bit tempera-
ture data can be obtained by reading the 8 MSBs from the T em-
perature Value Register (Address 27h) and the LSB from Bit 7
of the T emperature Configuration Register (Address 4Bh).
T he format of the temperature data is shown in T able II. T heo-
retically, the temperature sensor and ADC can measure tem-
peratures from –128
°
C to +127
°
C with a resolution of 0.5
°
C,
although temperatures below –40
°
C and above +125
°
C are
outside the operating temperature range of the device.
T able II. T emperature Data Format
T emperature
–128
°
C
–125
°
C
–100
°
C
–75
°
C
–50
°
C
–25
°
C
–0.5
°
C
0
°
C
+0.5
°
C
+10
°
C
+25
°
C
+50
°
C
+75
°
C
+100
°
C
+125
°
C
+127
°
C
Digital Output
1 0000 0000
1 0000 0110
1 0011 1000
1 0110 1010
1 1001 1100
1 1100 1110
1 1111 1111
0 0000 0000
0 0000 0001
0 0001 0100
0 0011 0010
0 0110 0100
0 1001 0110
0 1100 1000
0 1111 1010
0 1111 1111
LIMIT VALUE S
Limit values for analog measurements are stored in the appro-
priate limit registers. In the case of voltage measurements, high
and low limits can be stored so that an interrupt request will be
generated if the measured value goes above or below acceptable
values. In the case of temperature, a Hot T emperature Limit
can be programmed, and a Hot T emperature Hysteresis Limit,
which will usually be some degrees lower. T his can be useful as
it allows the system to be shut down when the hot limit is ex-
ceeded, and automatically restarted when it has cooled down to
a safe temperature.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM9240ARU | Low Cost Microprocessor System Hardware Monitor |
| ADM9261 | Triple- Power Supply Monitor(3路電源監視器) |
| ADM9264ARN-REEL | Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN-REEL7 | Quad Power Supply Monitor for Desktop PCs |
| ADM9264 | Quad Power Supply Monitor for Desktop PCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM9240ARU | 制造商:Analog Devices 功能描述:Data Acquisition System, 6 Channel, 9 Bit, 24 Pin, Plastic, TSSOP |
| ADM9240ARU-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost Microprocessor System Hardware Monitor |
| ADM9240ARU-REEL7 | 制造商:Analog Devices 功能描述: |
| ADM9264 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN | 制造商:Analog Devices 功能描述:Volt Supervisor Monitor 2.8V/3.3V/5V/12V 16-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:MULTI-SUPPLY HARDWARE MON - Bulk |
發布緊急采購，3分鐘左右您將得到回復。