- 您現在的位置：買賣IC網 > PDF目錄1898 > ADM3053BRWZ-REEL7 (Analog Devices Inc)IC TXRX ISOLATED CAN 20SOIC PDF資料下載
參數資料
| 型號： | ADM3053BRWZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX ISOLATED CAN 20SOIC |
| 產品培訓模塊： | iCoupler Digital Isolater Technology |
| 標準包裝： | 400 |
| 系列： | IsoPower®, iCoupler® |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 3.3V，5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC W |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Data Sheet
ADM3053
Rev. B | Page 15 of 20
APPLICATIONS INFORMATION
PCB LAYOUT
The ADM3053 signal and power isolated CAN transceiver
contains an isoPower integrated dc-to-dc converter, requiring
no external interface circuitry for the logic interfaces. Power
supply bypassing is required at the input and output supply pins
(see Figure 28). The power supply section of the ADM3053 uses
a 180 MHz oscillator frequency to pass power efficiently through
its chip-scale transformers. In addition, the normal operation of
the data section of the iCoupler introduces switching transients
on the power supply pins.
Bypass capacitors are required for several operating frequencies.
Noise suppression requires a low inductance, high frequency
capacitor, whereas ripple suppression and proper regulation
require a large value capacitor. These capacitors are connected
between GND1 and Pin 6 (VIO) for VIO. It is recommended that
a combination of 100 nF and 10 nF be placed as shown in Figure
28 (C6 and C4). It is recommended that a combination of two
capacitors, with values of 100 nF and 10 μF, are placed between
and C1). The VISOIN and VISOOUT capacitors are connected between
Pin 11 (GND2) and Pin 12 (VISOOUT) with recommended values
of 100 nF and 10 μF as shown in Figure 28 (C5 and C8). Two
capacitors are recommended to be fitted Pin 19 (VISOIN) and Pin 20
(GND2) with values of 100nF and 10nF as shown in Figure 28
(C9 and C7). The best practice recommended is to use a very low
inductance ceramic capacitor, or its equivalent, for the smaller
value. The total lead length between both ends of the capacitor
and the input power supply pin should not exceed 10 mm.
0929
3-
012
Figure 28. Recommended PCB Layout
In applications involving high common-mode transients, ensure
that board coupling across the isolation barrier is minimized.
Furthermore, design the board layout such that any coupling
that does occur equally affects all pins on a given component
side. Failure to ensure this can cause voltage differentials between
pins exceeding the absolute maximum ratings for the device,
thereby leading to latch-up and/or permanent damage.
The ADM3053 dissipates approximately 650 mW of power
when fully loaded. Because it is not possible to apply a heat sink
to an isolation device, the devices primarily depend on heat
dissipation into the PCB through the GND pins. If the devices
are used at high ambient temperatures, provide a thermal path
from the GND pins to the PCB ground plane. The board layout
in Figure 28 shows enlarged pads for Pin 1, Pin 3, Pin 9, Pin 10,
Pin 11, Pin 14, Pin 16, and Pin 20. Implement multiple vias from
the pad to the ground plane to reduce the temperature inside the
chip significantly. The dimensions of the expanded pads are at
the discretion of the designer and dependent on the available
board space.
EMI CONSIDERATIONS
The dc-to-dc converter section of the ADM3053 must, of
necessity, operate at very high frequency to allow efficient
power transfer through the small transformers. This creates
high frequency currents that can propagate in circuit board
ground and power planes, causing edge and dipole radiation.
Grounded enclosures are recommended for applications that
use these devices. If grounded enclosures are not possible, good
RF design practices should be followed in the layout of the PCB.
See the AN-0971 Application Note, Control of Radiated Emissions
with isoPower Devices, for more information.
INSULATION LIFETIME
All insulation structures eventually break down when subjected to
voltage stress over a sufficiently long period. The rate of insulation
degradation is dependent on the characteristics of the voltage
waveform applied across the insulation. Analog Devices conducts
an extensive set of evaluations to determine the lifetime of the
insulation structure within the ADM3053.
Accelerated life testing is performed using voltage levels higher
than the rated continuous working voltage. Acceleration factors for
several operating conditions are determined, allowing calculation
of the time to failure at the working voltage of interest. The values
shown in Table 5 summarize the peak voltages for 50 years of
service life in several operating conditions. In many cases, the
working voltage approved by agency testing is higher than the 50
year service life voltage. Operation at working voltages higher than
the service life voltage listed leads to premature insulation
failure.
The insulation lifetime of the ADM3053 depends on the voltage
waveform type imposed across the isolation barrier. The iCoupler
insulation structure degrades at different rates, depending on
whether the waveform is bipolar ac, unipolar ac, or dc. Figure 29,
Figure 30, and Figure 31 illustrate these different isolation voltage
waveforms.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM3054BRWZ-RL7 | IC TXRX CAN HS 16SOIC |
| ADM3071EARZ | IC TXRX RS-485 3.3V FD 8-SOIC |
| ADM3101EARQZ-REEL | IC TXRX RS-232 3.3V 15KV 16QSOP |
| ADM3232EARWZ | IC RCVR/LINEDRIVER RS232 16SOIC |
| ADM3251EARWZ | IC TXRX RS232 ISOLATED 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM3054 | 制造商:Analog Devices 功能描述:IC CAN TRANSCEIVER 1MBPS 16SOIC 制造商:Analog Devices 功能描述:IC, CAN, TRANSCEIVER, 1MBPS, 16SOIC 制造商:Analog Devices 功能描述:IC, CAN, TRANSCEIVER, 1MBPS, 16SOIC; Interface Type:CAN; No. of TX Buffers:1; No. of RX Buffers:1; Supply Voltage Min:3V; Supply Voltage Max:5.5V; Digital IC Case Style:SOIC; No. of Pins:16; Operating Temperature Min:-40C; Operating;RoHS Compliant: Yes |
| ADM3054BRWZ | 功能描述:IC TRANSCEIVER CAN 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:* 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| ADM3054BRWZ | 制造商:Analog Devices 功能描述:IC Interface Type:- No. of TX Buffers |
| ADM3054BRWZ-RL7 | 功能描述:IC TXRX CAN HS 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:* 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| ADM3054WBRWZ-RL7 | 功能描述:CAN Digital Isolator 5000Vrms 3 Channel 1Mbps 25kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包裝:剪切帶（CT） 零件狀態:有效 技術:磁耦合 類型:CAN 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:1/2 通道類型:單向 電壓 - 隔離:5000Vrms 共模瞬態抗擾度（最小值）:25kV/μs 數據速率:1Mbps 傳播延遲 tpLH / tpHL（最大值）:- 脈寬失真（最大）:- 上升/下降時間（典型值）:- 電壓 - 電源:3.3V，5V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:16-SOIC 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。