參數資料
型號: ADM2490EBRWZ
廠商: Analog Devices Inc
文件頁數: 6/16頁
文件大?。?/td> 0K
描述: IC TXRX RS-485 ISOLATED 16-SOIC
產品培訓模塊: iCoupler Digital Isolater Technology
標準包裝: 47
系列: iCoupler®
類型: 收發器,隔離式
驅動器/接收器數: 1/1
規程: RS422/RS485
電源電壓: 3V,5V
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 16-SOIC
包裝: 管件
產品目錄頁面: 790 (CN2011-ZH PDF)
ADM2490E
Rev. A | Page 14 of 16
APPLICATIONS INFORMATION
ISOLATED POWER SUPPLY CIRCUIT
The ADM2490E requires isolated power capable of 5 V at up
to approximately 65 mA (this current is dependent on the data
rate and termination resistors used) to be supplied between the
VDD2 and the GND2 pins. A transformer driver circuit with a
center-tapped transformer and LDO can be used to generate the
isolated 5 V supply, as shown in Figure 25. The center-tapped
transformer provides electrical isolation of the 5 V power supply.
The primary winding of the transformer is excited with a pair of
square waveforms that are 180° out of phase with each other. A
pair of Schottky diodes and a smoothing capacitor are used to
create a rectified signal from the secondary winding. The ADP3330
linear voltage regulator provides a regulated power supply to the
bus-side circuitry (VDD2) of the ADM2490E.
PCB LAYOUT
The ADM2490E isolated RS-485 transceiver requires no external
interface circuitry for the logic interfaces. Power supply bypass-
ing is required at the input and output supply pins (see Figure 24).
Bypass capacitors are conveniently connected between Pin 1
and Pin 2 for VDD1 and between Pin 15 and Pin 16 for VDD2. The
capacitor value should be between 0.01 μF and 0.1 μF. The total
lead length between both ends of the capacitor and the input
power-supply pin should not exceed 20 mm. Bypassing between
Pin 1 and Pin 8 and between Pin 9 and Pin 16 should also be
considered unless the ground pair on each package side is
connected close to the package.
VDD1
GND1
RxD
NC
GND1
TxD
NC
GND1
VDD2
GND2
A
B
NC
Z
Y
GND2
NC = NO CONNECT
ADM2490E
0
58
89
-01
3
Figure 24. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, care
should be taken to ensure that board coupling across the isola-
tion barrier is minimized. Furthermore, the board layout should
be designed such that any coupling that does occur equally affects
all pins on a given component side. Failure to ensure this could
cause voltage differentials between pins exceeding the absolute
maximum ratings of the device, thereby leading to latch-up or
permanent damage.
ISOLATION
BARRIER
VCC
78253 SD103C
SD103C
22F
10F
5V
OUT
IN
SD
GND ERR
VCC
VDD1
VDD2
GND1
GND2
TRANSFORMER
DRIVER
VCC
ADP3330
ADM2490E
05
88
9-
0
12
Figure 25. Isolated Power-Supply Circuit
相關PDF資料
PDF描述
ADM2491EBRWZ-REEL7 IC TXRX HS ESD PROT ISO 16SOIC
ADM2587EBRWZ IC TXRX RS485 ISOLATED 20SOIC
ADM3051CRZ IC TXRX CAN 24V 1MBPS 8SOIC
ADM3052BRWZ-REEL7 IC TXRX ISOLATED CAN 16SOIC
ADM3053BRWZ-REEL7 IC TXRX ISOLATED CAN 20SOIC
相關代理商/技術參數
參數描述
ADM2490EBRWZ-REEL7 功能描述:IC TXRX RS-485 HS ESD 16-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:iCoupler® 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232,RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC 包裝:管件
ADM2490EBRWZ-REEL71 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed, ESD-Protected, Full-Duplex, iCoupler, Isolated RS-485 Transceiver
ADM2491E 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed, ESD-Protected, Half-/Full-Duplex, iCoupler Isolated RS-485 Transceiver
ADM2491EBRWZ 功能描述:IC TXRX ISO RS-485 HS ESD 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP(0.209",5.30mm 寬) 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2
ADM2491EBRWZ 制造商:Analog Devices 功能描述:IC RS-485 TRANSCEIVER 5.5V SOIC-16 制造商:Analog Devices 功能描述:IC, RS-485 TRANSCEIVER, 5.5V, SOIC-16