- 您現在的位置：買賣IC網 > PDF目錄375257 > ADM1170-1AUJZ-RL7 (ANALOG DEVICES INC) 1.6 V to 16.5 V Hot Swap Controller with Soft Start PDF資料下載
參數資料
| 型號： | ADM1170-1AUJZ-RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1.6 V to 16.5 V Hot Swap Controller with Soft Start |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | LEAD FREE, MO-193BA, TSOT-8 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 168K |
| 代理商： | ADM1170-1AUJZ-RL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
ADM1170
gate voltage of the external FET. This minimizes the bus supply
voltage drop caused by the fault and protects neighboring cards.
Rev. 0 | Page 12 of 16
As the voltage across the sense resistor approaches the current
limit, a timer activates. This timer resets again if the sense
voltage returns below this level. If the sense voltage is any
voltage below 44 mV, the timer is guaranteed to be off. Should
the current continue to increase, the ADM1170 tries to regulate
the gate of the FET to achieve a limit of 50 mV across the sense
resistor. However, if the device is unable to regulate the fault
current and the sense voltage further increases, a larger pull-
down, in the order of milliamperes, is enabled to compensate
for fast current surges. If the sense voltage is any voltage greater
than 56 mV, this pull-down is guaranteed to be on. When the
timer expires, the GATE pin shuts down.
TIMER FUNCTION
The TIMER pin is responsible for several key functions on the
ADM1170. A capacitor controls the initial power on reset time
and the amount of time an overcurrent condition lasts before
the FET shuts down. On the ADM1170-1, the timer pin also
controls the time between auto retry pulses. There are pull-up
and pull-down currents internally available to control the timer
functions. The voltage on the TIMER pin is compared with two
threshold voltages: COMP1 (0.2 V) and COMP2 (1.3 V). The
four timing currents are listed in Table 5.
Table 5.
Timing Current
Pull-up
Pull-up
Pull-down
Pull-down
Level (μA)
5
60
2
100
POWER-UP TIMING CYCLE
The ADM1170 is in reset when the ON (ON-CLR) pin is held
low. The GATE pin is pulled low and the TIMER pin is pulled
low with a 100 μA pull-down. At Time Point 2 in Figure 33, the
ON (ON-CLR) pin is pulled high. For the device to startup
correctly, the supply voltage must be above UVLO, the ON
(ON-CLR) pin must be above 1.3 V, and the TIMER pin voltage
must be less than 0.2 V The initial timing cycle begins when these
three conditions are met, and the TIMER pin is pulled high with
5 μA. At Time Point 3, the TIMER reaches the COMP2 threshold.
This is the end of the first section of the initial cycle. The 100 μA
current source then pulls down the TIMER pin until it reaches
0.2 V at Time Point 4. The initial cycle delay (Time Point 2 to
Time Point 4) relates to C
TIMER
by equation
t
INITIAL
= 1.3 ×
C
TIMER
/5 μA
(4)
When the initial cycle ends, a start-up cycle activates and the
GATE pin is pulled high; the TIMER pin continues to pull down.
1
2
NORMAL
CYCLE
INITIAL
CYCLE
START-UP
CYCLE
RESET
MODE
3
4
V
IN
V
ON
V
TIMER
V
GATE
V
OUT
0
Figure 33. Power-Up Timing
2μA
5μA
60μA
100μA
V
IN
V
ON
V
TIMER
V
GATE
V
OUT
I
RSENSE
NORMAL
CYCLE
INITIAL
CYCLE
START-UP
CYCLE
RESET
MODE
Figure 34. Power-Up into Capacitor
0
CIRCUIT BREAKER TIMING CYCLE
When the voltage across the sense resistor exceeds the circuit
breaker trip voltage, the 60 μA timer pull-up current is activated.
If the sense voltage falls below this level before the TIMER pin
reaches 1.3 V, the 60 μA pull-up is disabled and the 2 μA pull-
down is enabled. This is likely to happen if the overcurrent fault
is only transient, such as an inrush current. This is shown in
Figure 34. However, if the overcurrent condition is continuous
and the sense voltage remains above the circuit breaker trip
voltage, the 60 μA pull-up remains active. This allows the TIMER
pin to reach the high trip point of 1.3 V and initiate the GATE
shutdown. On the ADM1170-2, the TIMER pin continues pulling
up but switches to the 5 μA pull-up when it reaches the 1.3 V
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1170-2AUJZ-RL7 | 1.6 V to 16.5 V Hot Swap Controller with Soft Start |
| ADM1171 | 2.7 V to 16.5 V Hot Swap Controller with Current Sense Output |
| ADM1171-1AUJZ-RL7 | 2.7 V to 16.5 V Hot Swap Controller with Current Sense Output |
| ADM1171-2AUJZ-RL7 | 2.7 V to 16.5 V Hot Swap Controller with Current Sense Output |
| ADM1175 | Hot Swap Controller and Digital Power Monitor with Convert Pin |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1170-2AUJZ-RL7 | 功能描述:IC CTRLR HOTSWAP 16.5V TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| ADM1171 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 16.5 V Hot Swap Controller with Current Sense Output |
| ADM1171-1AUJ | 制造商:Analog Devices 功能描述:ADI HOT SWAP CONTROLLER - Bulk |
| ADM1171-1AUJZ-RL7 | 功能描述:IC CTRLR HOTSWAP 16.5V TSOT-23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| ADM1171-2AUJ | 制造商:Analog Devices 功能描述:ADI HOT SWAP CONTROLLER - Bulk |
發布緊急采購，3分鐘左右您將得到回復。