參數資料
型號： ADM1041ARQ
廠商： ANALOG DEVICES INC
元件分類： 通信及網絡
英文描述： Secondary-Side Controller with Current Share and Housekeeping
中文描述： SPECIALTY TELECOM CIRCUIT, PDSO24
封裝： MO-137AE, QSOP-24
文件頁數： 30/64頁
文件大?。?/td> 1063K
代理商： ADM1041ARQ
ADM1041
OSCILLATOR AND TIMING GENERATORS
An on-board oscillator is used to generate timing signals. Some
trimming of the oscillator is provided to adjust for variations in
processing.
Rev. A | Page 30 of 64
All timing generated from the oscillator is expected to meet the
same tolerances as the oscillator. Since individual delay counters
are generally two to three bits, the worst error is one clock period
into these counters, which is 25% of the nominal delay period.
None of these tolerances are extremely critical.
LOGIC I/O AND MONITOR PINS
Apart from pins required for the various key analog functions, a
number of pins are used for logic level I/O signals. If the logic
I/O function is not required, the pins may be reconfigured as
general-purpose comparators for analog level monitoring (MON)
and may be additionally configured to have typical OVP and
UVP properties, either positive-going or negative-going,
depending on whether a positive supply output or a negative
supply output is being monitored. When monitoring negative
outputs, a positive bias must be applied via a resistor to V
REF
.
The status of all protection and monitoring comparators are
held in registers that can be read by a microprocessor via the
SMBus. Certain control bits may be written to via the SMBus.
CBD/ALERT
This pin can be used either as a crowbar driver or as an SMBus
alert signal to indicate that a fault has occurred. It is typically
configured to respond to a variety of status flags, as detailed in
Registers 1Ah and 1Bh. The primary function of this pin is as a
crowbar driver, and as such it should be configured to respond
to the OV fault status flag. It can be configured to respond to
any or all of a variety of fault status flags, including a micro-
processor writable flag, and can be configured as latching or
nonlatching. It may also be configured as an open-drain
N-channel or P-channel MOSFET and as positive or negative
(inverted) logic. A pull-up or pull-down resistor is required.
This pin may be wire-ORed with the same pin on other
ADM1041 ASICs in the power supply.
The alternative function is an SMBus alert output that can be
used as an interrupt to a microprocessor. If a fault occurs, the
microprocessor can then query the ADM1041(s) about the fault
status. This is intended to avoid continuously polling the
ADM1041(s).
Generally, the microprocessor needs to routinely gather other
data from the ADM1041(s), which can include the fault status,
so the ALERT function may not be used. Also, the simplest
microprocessors may not have an interrupt function. This
allows the CBD/ALERT pin to be used for other functions.
MON1
This is the alternative analog comparator function for the
Pulse/AC
SENSE
1 pin (Pin 9). The threshold is 1.25 V. When
MON1 is selected, AC
SENSE
1 defaults to true.
MON2
This is the alternative analog comparator function for the
AC
SENSE
2 pin (Pin 10). The threshold is 1.25 V. When MON2 is
selected, AC
SENSE
2 defaults to true.
PEN
This is the power enable pin that turns the PWM converter on
and can be configured as active high or low. This might drive an
opto-isolator back to the primary side or connect to the enable
pin of a secondary-side post regulator.
PSON
This pin is usually connected to the customer’s PSON signal
and, when asserted, causes the ADM1041 to turn on the power
output. It can be configured as active high or low. Alternatively,
a microprocessor can communicate the PSON function to the
ADM1041 using the SMBus. Or the PS
ON
LINK signal may be
used. When the PSON pin is not used as such it can be
configured as an analog input, MON3.
MON3
This is the alternative analog comparator function for the PSON
pin (Pin 16). The threshold is 1.25 V. When MON3 is selected,
PS ON defaults to off.
DC_OK (PW-OK, PWR Good, Etc.)
This output is true when all dc output voltages are within toler-
ance and goes false to signify an imminent loss of power. Timing
is discussed later. It can be configured as an open-drain N-
channel or P-channel MOSFET and as positive or negative
(inverted) logic. A pull-up or pull-down resistor is required.
This pin may be wire-ORed with the same pin on other
ADM1041 ASICs in the power supply. When the DC_OK pin is
not used as such, it can be configured as an analog input,
MON4.
MON4
This is the alternative analog comparator function for the
DC_OK pin (Pin 17). The threshold is 1.25 V.
V
REF
This pin normally provides a precision 2.5 V voltage reference.
Alternatively, it can be configured as the AC_OK output or as
an analog input, MON5. A load capacitance of 1 nF (typ) is
recommended on V
REF
.
相關PDF資料
PDF描述
ADM1041A Secondary-Side Controller with Current Share and Housekeeping
ADM1041AARQZ Secondary-Side Controller with Current Share and Housekeeping
ADM1041AARQZ-REEL Secondary-Side Controller with Current Share and Housekeeping
ADM1041AARQZ-REEL7 Secondary-Side Controller with Current Share and Housekeeping
ADM1052 Precision Dual Voltage Regulator Controller
相關代理商/技術參數
參數描述
ADM1041ARQ-2 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADM1041ARQ-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping
ADM1041ARQ-REEL7 功能描述:IC PWR SUP MON/LOAD SHARE 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
ADM1041ARQZ 功能描述:IC PWR SUPP MON/LOAD SHAR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
ADM1041ARQZ-REEL 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*